This topic has been archived. It cannot be replied.
-
枫下家园 / 美丽家居 / 这个个问题和车无关但不知道去哪问,借本坛问一下。有个工具的小零件的两片铁应该是焊在一起的被摔开了,怎么可以把它们粘或焊回去?
-anim8(what);
2020-10-21
{55}
(#13255071@0)
+1
-
找台接触焊机,焊回去。粘是粘不住的。
-1world(北京旗人之灭中国病毒);
2020-10-21
(#13255086@0)
-
不知道去哪里找接焊机也不会焊
-anim8(what);
2020-10-21
(#13255225@0)
-
这是点焊(spot welding)的。不会钻孔的话,到华人修车店换油时请他们给你用电焊在侧面点两下。
-baisilver333(INITIATIVE);
2020-10-21
(#13255269@0)
+1
-
谢谢,车刚换油,先去修车店试试看有愿意做的吗
-anim8(what);
2020-10-22
(#13256948@0)
-
打2個小洞,用咬口螺絲旋緊。
-youarenotfunnyatall(草山);
2020-10-21
(#13255103@0)
-
这也是我觉得能做到的,加一块铁夹紧
-anim8(what);
2020-10-21
(#13255229@0)
-
如果不拆,鎖緊之前,加些super glue 在中間,就足夠了.
-youarenotfunnyatall(草山);
2020-10-21
(#13255486@0)
-
去修车店他们说没焊机,只好这样做了,看能用不
-anim8(what);
2020-10-22
{166}
(#13258159@0)
-
我現在明白為什麼你說管子裡不能放東西了。可能只能焊。是有些麻煩。
-youarenotfunnyatall(草山);
2020-10-22
(#13258276@0)
-
你就在论坛里拜求一下,应该会有人联系你帮你焊一下,前两天不还有个网友买了焊机。
-bigcatf2(ToBe);
2020-10-22
(#13258316@0)
-
看来改天另开一帖拜求
-anim8(what);
2020-10-22
(#13258788@0)
-
找厂家,要新的。要么买新的。其他甭合计了。
-troyd(Troy);
2020-10-21
(#13255247@0)
-
旧工具但日常使用,没钱买新的,上面伙计建议打两洞夹起能解决就行了
-anim8(what);
2020-10-21
(#13255328@0)
-
if so,别忘了椭圆管里也放个固定的小 cube,然后用 lock nuts。
-troyd(Troy);
2020-10-21
(#13255367@0)
-
里面放东西就不能用了
-anim8(what);
2020-10-22
(#13256949@0)
-
JB welder
-china-cat(chinacat);
2020-10-21
(#13255533@0)
-
JB welder 怕不够强吧?
-anim8(what);
2020-10-22
(#13256951@0)
-
JB强度还是可以的要不也不能叫welder了,要买好的。
-zhengsean(IT大叔);
2020-10-22
(#13257754@0)
-
打洞,用铆钉
-company(Money Trees);
2020-10-22
(#13256972@0)
+1
-
这个感觉只能焊。打洞上螺丝胶粘都是学者型的理论,只值得敬佩
-cocnut(tz);
2020-10-22
(#13257861@0)
-
焊没有了,学者加diy JB weld 夹铁片看看
-anim8(what);
2020-10-22
(#13258181@0)
-
如果工具吃力较大,个人的方法会把原来的点焊2点打磨干净,再把短圆扁管和L型件对接处的侧面脏污或油漆用砂纸或wheel brush清洁好后找有焊机的车行或者朋友帮忙在每侧各2处点焊足够(焊接时用Vise或C - Clamp固定)。JB Welder粘接强度不错的可以试试
-sthbay(大曈);
2020-10-22
(#13258223@0)
-
原来点焊有两点突出我没办法磨平,所以在另加铁片也JB焊了,有用砂纸了的
-anim8(what);
2020-10-22
(#13258239@0)
-
点焊的地方用锉刀搓掉,如果有焊机的话,两个工件连接的地方左右各焊一条缝。对焊功要求有点高。
-coolrock(coolrock);
2020-10-22
(#13258253@0)
-
楼上说焊回去的 也不想一想,分开的两件都是Square Tube,如何焊在一块? 如果没有特殊 焊具。
-anexplorer(页于);
2020-10-22
(#13258233@0)
-
如图
-anim8(what);
2020-10-22
{55}
(#13258241@0)
-
不找 steel fabrication shop,无解。别折腾了。就是找了,估计也是无解。
-troyd(Troy);
2020-10-22
{24}
(#13258295@0)
-
既然用一块铁片和小螺栓螺母这么弄,为何不去找Two Hole EMT Strap 或者 Hanger Strapping来弄,不是比用一块铁片更好看也更牢靠些么?或截一小段铝条紧贴着那管的形状折好后,在合适地方钻孔再用螺栓紧上...
-see1see(Isee);
2020-10-22
(#13258360@0)
-
哇哇哇!!!想不到有这麽多脑洞大开的答复。不过麽,问题这么的模糊,热心的人又这多,也难怪。其实呀实际中一般问题说清楚了,解决方案也就很快出来了。
-888www888(HHH);
2020-10-22
(#13258781@0)
+2
-
实际这是个写生画架托画板的,现实中有很多解决方案但是这个比较利索方便,这玩意我前两天才$20掏的二手才用一回就摔到水泥地就这样了,当然花钱的话更好的解决方案都有,但是不花钱凑合也可以用所以就让我想diy了
-anim8(what);
2020-10-22
(#13258828@0)
+1
-
图
-anim8(what);
2020-10-22
{55}
(#13258837@0)
+1
-
唉,早点拿出完整照片来嘛,那个脱落的其实是个带滑套的托架吧?需要能上下滑动然后还可以拧紧固定对吧?太好办了,就在十字交叉点钻一个孔但仅钻穿滑套的一面,用一个螺栓或螺钉拧进去,需滑动时松螺钉,需固定时拧紧...
-see1see(Isee);
2020-10-22
(#13258910@0)
-
这个方案的问题是螺栓头的地方是放画板的
-anim8(what);
2020-10-22
(#13258938@0)
-
原来你是小画家!难怪做出的东西与别人不一样。众人的审美观有待提高!
-cocnut(tz);
2020-10-22
(#13259036@0)
-
给小孩用的
-anim8(what);
2020-10-22
(#13259126@0)
-
这么说来,这个物件是“写生画架托画板”上的一个配件,看起来它还可以沿一个管件滑动。承载不是太大,若干公斤左右。既然如此,上面各位网友的建议看来都基本可行。焊接最好,如果能买到高级胶,估计也不会差;螺接的不太好看,铆接估计也行如果能买到铝铆钉的话。
Home depot / Candia Tire有铜焊/铅焊工具,
-888www888(HHH);
2020-10-22
{277}
(#13258878@0)
+2
-
嗯,托的东西不重最多两三磅
-anim8(what);
2020-10-22
(#13258898@0)
-
为这不值钱的东西折腾有点不好意思
-anim8(what);
2020-10-22
(#13258884@0)
-
Home depot / Candia Tire有铜焊/铅焊工具, easy for DIY. Enjoy it!
-888www888(HHH);
2020-10-22
(#13258897@0)
+2
-
水管工那种吗?
-anim8(what);
2020-10-22
(#13258902@0)
-
yes. very easy. using gas.
-888www888(HHH);
2020-10-22
(#13258905@0)
+2
-
谢谢🙏
-anim8(what);
2020-10-22
(#13258908@0)
-
这么麻烦!哪天拿来我给你电焊一下。先声明:不是专业的,沾上就算。
-cityaround(求雨山);
2020-10-23
(#13259268@0)
-
谢谢🙏大侠!!!
-anim8(what);
2020-10-23
(#13259303@0)
-
貌似只有肉联才有这种暖心的回复嘛,特地来赞一下!
-see1see(Isee);
2020-10-24
(#13263067@0)
-
早说用途啊。这个载荷不大,用JB welder完全可以,我记得它宣称强度可达400MPA
-baisilver333(INITIATIVE);
2020-10-24
(#13263036@0)