This topic has been archived. It cannot be replied.
-
枫下家园 / 美丽家居 / 请问大家,DIY 装车库门opener 难度系数有多大? DIY干这活是扣门还是.....?
-anim8(what);
2020-9-1
(#13166737@0)
-
两到五个小时
-skybreeze(天涯的风);
2020-9-1
(#13166740@0)
-
难不难?
-anim8(what);
2020-9-1
(#13166744@0)
-
手册指南不清晰,需要琢磨一下
-skybreeze(天涯的风);
2020-9-1
(#13166757@0)
-
🙏
-anim8(what);
2020-9-1
(#13166872@0)
-
要看很多YouTube吗?
-anim8(what);
2020-9-1
(#13166746@0)
-
看管用。手册很差。
-skybreeze(天涯的风);
2020-9-1
(#13166753@0)
-
分人了。你就应该试一试。你喜欢撞南墙,或者少一事不如多一事。
-2841999(四友);
2020-9-1
(#13166754@0)
-
我怕说请人装的话显得自己又懒又笨,硬头皮干又很有可能撞南墙,或者啥也不干将就用下去........你做哪个台阶挖桩难不难?我也想挖但是怕靠近房子回填都建筑垃圾石头砖块之类
-anim8(what);
2020-9-1
(#13166771@0)
-
光那个铲子的话没有把握。因为挖下去不知道能碰到什么硬东西。再有一根钢钎就信心满满了。
-2841999(四友);
2020-9-1
(#13166798@0)
-
那个铲店里卖的把太短,挖深一点就腰得受罪了,看人家补漏的那个才够专业
-anim8(what);
2020-9-1
(#13166813@0)
-
光是装个opener应该不难,麻烦是装车库门轨道。。。
-ding_ding(丁_丁);
2020-9-1
(#13166750@0)
+1
-
不能用原来的轨吗?
-anim8(what);
2020-9-1
(#13166772@0)
-
车库门的导轨不用换,就换传感器,链条,链条的导轨和新的opener。我一个人2-3个小时完成。装链条导轨时用绳子吊住一头再安装另外一头就可以。
-jiaji(加吉);
2020-9-3
(#13168944@0)
-
🐂!
-anim8(what);
2020-9-3
(#13169435@0)
-
不难 我装过仨了
-facenorthface(小北);
2020-9-1
(#13166760@0)
+1
-
三车库👍
-skybreeze(天涯的风);
2020-9-1
(#13166763@0)
-
自己的和朋友们的😄
-facenorthface(小北);
2020-9-2
(#13167576@0)
-
是原来是chain改皮带的吗?
-anim8(what);
2020-9-1
(#13166774@0)
-
都是chain
-facenorthface(小北);
2020-9-2
(#13167575@0)
-
这,,,有 3 个家的人,,,不多啊,,,
-troyd(No news is bad news);
2020-9-1
(#13166786@0)
-
嗯 我把朋友家当自己家的
-facenorthface(小北);
2020-9-2
(#13167577@0)
-
不难,中途最好有人帮忙托一下,或者拿个梯子架着也行
-honeylager(No Name);
2020-9-1
(#13166779@0)
-
谢谢
-anim8(what);
2020-9-1
(#13166787@0)
-
如果是有大弹簧的门,系数是 100%,如果没有弹簧门,门现在状态是好的,系数小于 10%。
-troyd(No news is bad news);
2020-9-1
(#13166784@0)
-
没见过没大弹簧的门啊
-anim8(what);
2020-9-1
(#13166792@0)
-
还有没弹簧的门?
-skybreeze(天涯的风);
2020-9-1
(#13166800@0)
-
哦,commercial 的门都是 chain, cable, 等的。。。对不起,,,脑子短了回路。
-troyd(No news is bad news);
2020-9-1
(#13166819@0)
-
自己装过一台,不难,也不需要看youtube,设备随带的说明写的很清楚,按照说明装就可以了。
-cocnut(tz);
2020-9-1
(#13166867@0)
+1
-
🙏
-anim8(what);
2020-9-1
(#13166873@0)
-
如果目前已经有opener,只是换一个新的很简单。如果啥都没有,从轨道安装开始的话,难度会比较大,一般人不一定能搞定。
-coolrock(coolrock);
2020-9-1
(#13166909@0)
-
有,是三十年的Stanley, keypad密码没记住想换,做车库门的说太老了,
-anim8(what);
2020-9-1
(#13166918@0)
-
如果只是遥控不干活的话不用换opener,换那个手动开关为遥控即可。20分钟搞定
-abcdefghi(9alphabetic);
2020-9-1
(#13167341@0)
-
你是说把车库内墙上的开关弄成遥控吗?,怎么弄?
-anim8(what);
2020-9-1
(#13167353@0)
-
超级容易。也不是非改那开关,并联一个即可。并联的可直接固定到opener或附近。Amazon上找一个,三四十刀
-abcdefghi(9alphabetic);
2020-9-1
(#13167361@0)
-
谢谢🙏
-anim8(what);
2020-9-1
(#13167472@0)
-
Stanley的旧的,密码可能是一排on off 开关,你抬头看一下,如果有那细细一排,那你到EBay Amazon买一个老遥控即可,更省事
-abcdefghi(9alphabetic);
2020-9-1
(#13167386@0)
-
哦,找老遥控,🙏
-anim8(what);
2020-9-1
(#13167459@0)
-
改密码就是改改那个on/off就可以吧?
-anim8(what);
2020-9-2
(#13167475@0)
-
现有遥控都可以用了,发现车上homelink也可以用来开门,但还没设置成功
-anim8(what);
2020-9-2
(#13167900@0)
-
要量一下你的车库门高度是八尺或是七尺。一般opener是以七尺为标准,如果是八尺要另外再买配件。
-cat1017(cat);
2020-9-1
(#13167053@0)
+1
-
🙏
-anim8(what);
2020-9-1
(#13167219@0)
-
有工具就不难,否则挺难的。那个长臂固定到墙上很费劲。还有把那个机器掉到天花板上可能要用锯断角钢。
-infinity7.1(notailor);
2020-9-1
(#13167356@0)
+1
-
哦……
-anim8(what);
2020-9-1
(#13167460@0)
-
换opener顶多算初中级。换弹簧有点难度,有风险,算中级。
-rogerscanner(Roger);
2020-9-1
(#13167370@0)
+2
-
哦
-anim8(what);
2020-9-1
(#13167461@0)
-
我曾今式装过一个、把opener的链条弄断了、最后还是找人120块修好,还试过两个车互相打火、结果电极接反了,车烧起来了,最后找人200换了个电池,我迄今为止DIY最成功的是换屋顶。
-xiangcaosh(船头);
2020-9-2
(#13167506@0)
-
鉴于你这么问,建议找人装。我安装过差不多10个了。最快也得几个小时。请人干这个很便宜的。
-lakota(lakota);
2020-9-2
(#13167553@0)
-
嗯,我不是很能还是请人算了,但是现在remote都可用就继续用先
-anim8(what);
2020-9-2
(#13167898@0)
-
最难的就是装opener本身,因为举架不同,厂家配件可能不够用。可自己先试一下:门框正中间往上找一个有木方的点,从这水平向里8ft就是opener齿轮的位置。如果能装好,其他就没什么了
-howtosay(咋说呢);
2020-9-2
(#13168440@0)
-
嗯,很多事情道理简单做起来这样那样问题
-anim8(what);
2020-9-2
(#13168484@0)
-
都是请人干的,几十元而已
-sixiang18(wang);
2020-9-2
(#13168450@0)
-
现在遥控换电池又继续用了,就几块钱,等人工再贵点再请人换呵呵
-anim8(what);
2020-9-2
(#13168473@0)