This topic has been archived. It cannot be replied.
-
枫下家园 / 美丽家居 / homedepot新买的门锁,装上去,可以锁,钥匙可以正常拔下来。可以正常开锁,问题就是开锁后,钥匙拔不下来,怎么换角度也拔不下来。尝试把里面或外面的部分转个180度安装,还是同样的问题,挺纳闷的,是锁的问题还是安装的问题?谢谢!
-summer1215(Springback);
2019-8-17
(#12278038@0)
-
这种锁
-summer1215(Springback);
2019-8-17
{61}
(#12278045@0)
-
估计是装反了
-padawan2018(Padawan);
2019-8-17
(#12278064@0)
+2
-
也想着装反了,换个角度装,还是同样的问题
-summer1215(Springback);
2019-8-17
(#12278537@0)
-
不会吧。开锁180度,再回90度,拔钥匙。
-badboy91(go wild);
2019-8-17
(#12278065@0)
-
回多少度,也拔不下来
-summer1215(Springback);
2019-8-17
(#12278535@0)
-
呵呵,拆锁,将扁平的撬棍拧个角度,正反各试一下。
-cityaround(求雨山);
2019-8-17
(#12278524@0)
-
不能调180度,90度试一下。
-cityaround(求雨山);
2019-8-17
(#12278526@0)
-
已经拆了好几遍了。你说的那个扁平的撬棍,端头是个长方体,不是正方体,所以只能换180度,没法调90度。真是奇了怪了
-summer1215(Springback);
2019-8-17
(#12278540@0)
-
要是新锁不会有问题的,可能是角度调整有差错。上照片让大伙参谋一下。
-cityaround(求雨山);
2019-8-18
(#12280976@0)
-
开锁后,钥匙拔不下来----钥匙没有转到位。
-hunhunhunhun(不知道);
2019-8-17
(#12278562@0)
-
检查一下钥匙的齿是否平滑。必要时稍微用砂纸打磨一下毛刺。锁孔里挤点WD40润滑一下。
-2841999(四友);
2019-8-17
(#12278563@0)
+1
-
如果锁芯有点像活塞一样往复进出,在拔钥匙的时候会随钥匙拔出一点。用指尖顶住锁芯拔。
-2841999(四友);
2019-8-17
(#12278565@0)
-
建议锁芯里不要用任何液体之类的润滑剂,刮点铅笔芯的粉末倒进去会惊讶得不行.......
-cityaround(求雨山);
2019-8-19
(#12283007@0)
-
会有完整的笔芯冒出来吗?
-winterfish(潜水鱼(\ (•◡•) /));
2019-8-19
(#12283029@0)
-
别挤wd40.那不是好东西。用硅胶类的润滑剂,喷的也行。
-3854688(小鹏);
2019-8-19
(#12283118@0)
-
你的问题有可能是锁的舌头没进到所需要的位置, 你可以不关门然后看看锁舌自由出来, 看看钥匙能不能拔出来, 如果还是拔不出来就说明锁有问题, 多半是空锁的时候没问题, 但到了洞里就卡住了, 这种情况你就要检查并挖深你的洞,再看看对准没, 是不是有擦边现象.
-yuanfanback(归来的远帆);
2019-8-18
(#12278839@0)
+1
-
这种deadend很饶人的,回复到插入位置能拔出来,只有那一个位置能拔出来
-googlebot(bot);
2019-8-19
(#12283016@0)
-
忽然觉得还是没完全明白你的问题:你说的是锁不上门还是钥匙根本拔不出来了?要是后者我告诉你什么问题。
-cityaround(求雨山);
2019-8-19
(#12283024@0)
-
感谢楼上各位回复。能锁,能开,在锁的状态下key能正常拔出。开的状态拔不出来。
-summer1215(Springback);
2019-8-19
(#12283175@0)
-
就是设计成这样的吧。怕你忘记锁门。
-ding_ding(丁_丁);
2019-8-19
(#12283179@0)
+1
-
汇报,装了拆,拆了装,拆,装,反复换角度,折腾了大概有十多次,终于终于好了。没加任何润滑剂。不知怎么好了。
-summer1215(Springback);
2019-8-19
(#12283180@0)
-
恭喜。不过机械的东西,润滑剂肯定是要的,只是别加wd40,那不是润滑剂
-3854688(小鹏);
2019-8-20
(#12283525@0)