This topic has been archived. It cannot be replied.
-
枫下家园 / 美丽家居 / 一大早火炉不工作了,昨晚还正常。怎么办啊?冷冷冷
-huanhuan2(Winter);
2018-12-27
{6}
(#11855802@0)
+5
-
火炉不停尝试点火,但起不来
-huanhuan2(Winter);
2018-12-27
(#11855808@0)
-
找人来修吧
-pumba(J哥);
2018-12-27
(#11855816@0)
+2
-
请推荐啊
-huanhuan2(Winter);
2018-12-27
(#11856146@0)
+1
-
打电话给暖气公司,账单上有他们的电话号码。 赶紧叫人来修,再冻下去小心水管爆裂
-anon(小城);
2018-12-27
(#11856256@0)
-
暖气炉是买下来的,没有账单
-huanhuan2(Winter);
2018-12-27
(#11856276@0)
+1
-
你在哪个市? 让大家帮忙上网查一下你那个市的暖气公司或服务公司
-anon(小城);
2018-12-27
(#11856298@0)
+1
-
Scarborough
-huanhuan2(Winter);
2018-12-27
(#11856303@0)
-
你查没查故障码啊? 有可能是thermocouple 需要清洁一下。
-ontario_2014(rolian);
2018-12-27
(#11855862@0)
-
thermocouple在哪里?什么样?
-huanhuan2(Winter);
2018-12-27
(#11855874@0)
-
就一类似细金属棍的温度传感器,中文名“热电偶”,用来检测温度,在这里是检测火苗。你google 一下,不能这么等或瞎试。
-ontario_2014(rolian);
2018-12-27
(#11856005@0)
-
拆下来,擦干净,装回去,依然
-huanhuan2(Winter);
2018-12-27
(#11856593@0)
-
怎么擦干净的?专业点儿应该用steel wool cloth 去把那些锈的擦掉才对,尽量去掉锈和烧黑的部分,但别用砂纸打磨。
-ontario_2014(rolian);
2018-12-28
(#11857288@0)
-
对,看视频说了。用厨房用的厚海绵擦的
-huanhuan2(Winter);
2018-12-28
(#11857419@0)
-
需要测量电流的,不是看起来干净。
-hunhunhunhun(不知道);
2018-12-29
(#11858831@0)
-
这是专业活,不会了
-huanhuan2(Winter);
2018-12-29
(#11859357@0)
-
没有故障码。ecobee没显示故障,但不断启动,打不着火。
-huanhuan2(Winter);
2018-12-27
(#11855884@0)
-
Ecobee 不会显示故障,是炉子下面有两个LED灯,通过显示状态告诉你大概故障,炉子上面应该有说明。如果你的是很老的炉子就没有了。
-ontario_2014(rolian);
2018-12-27
(#11856000@0)
-
若干年前,我家有类似现象。
-jetman(飞人);
2018-12-27
{336}
(#11856538@0)
-
左上角发黑那个焊点。
-jetman(飞人);
2018-12-27
{57}
(#11856578@0)
-
这个就太难检测了,专业级
-huanhuan2(Winter);
2018-12-27
(#11856595@0)
-
用手摇一摇煤气电磁阀上的cable harness,如果能正常工作一会,就是它的问题了。
-jetman(飞人);
2018-12-27
{36}
(#11856699@0)
-
摇了,铁管摇不动的
-huanhuan2(Winter);
2018-12-28
(#11857420@0)
-
Cable or wires 不是煤气管。
-jetman(飞人);
2018-12-28
(#11857452@0)
-
这个是煤气电磁开关,除了小黑软管,没有别的cable or wire.
-huanhuan2(Winter);
2018-12-28
{60}
(#11857478@0)
-
去检查排气管和进气管是否被雪埋了, 打开机箱看蒸馏水是否堵了,
-yuanfanback(归来的远帆);
2018-12-27
(#11855827@0)
-
今天没雪(多伦多)。上次开空调,冷凝水堵过,漏一地水。这次没有,刚拔下水管,用打气筒打气,没问题。
-huanhuan2(Winter);
2018-12-27
(#11855879@0)
-
可能点火器坏了
-dummyfrog(DummyFrog);
2018-12-27
(#11855928@0)
-
管子一般不会堵, 而是里面有个和管子接着的盛水的小黑盒子里可能堵了。。。
-guanshui88(约定);
2018-12-27
(#11855957@0)
-
小黑盒子是不是地上那个抽水泵?上次是水管进口堵了,空调水下不来,就四处漏
-huanhuan2(Winter);
2018-12-27
(#11855980@0)
-
再次拔下水管,插进一根一尽长的铁丝,没堵。
-huanhuan2(Winter);
2018-12-27
(#11855990@0)
+1
-
这是不是那个管子?
-huanhuan2(Winter);
2018-12-27
{60}
(#11856137@0)
-
哦, 没下雪啊, 那就看看能不能点火
-yuanfanback(归来的远帆);
2018-12-27
(#11856223@0)
-
您老又不在多伦多
-huanhuan2(Winter);
2018-12-27
(#11856592@0)
-
是啊,在魁北克, 我们这雪大.
-yuanfanback(归来的远帆);
2018-12-27
(#11856916@0)
-
一个奇怪的现象(可重复):温控设在 “Heat", 它就不停的"打火--停止"; 当设成"Off", 它先几次"打火--停止",然后”轰隆隆“好像正常启动一样,短暂一会儿就停止了。
-huanhuan2(Winter);
2018-12-27
(#11855997@0)
+1
-
先按上面的建議查看2個LED燈的燈態, 爐子上一般都會表明燈狀態代表什麼故障.1. 按上次積水, 有可能是裡面出水的管道被堵,打開爐子,看裡面是否有積水, 確認裡面通往外面的管道是通的
2. 換filter試試, 再關掉和打開爐子
按照我家爐子原來出現過的問題,就是內部管道積水導致很多異常, 後來我每年把內部管道通往外部的管道拔出來清理一遍,就再也沒有過不可思議的問題了, 然後就是filter的問題
-seaboy998(seaboy);
2018-12-27
{291}
(#11856011@0)
-
检查了filter,不算太脏。不知道怎么打开看里面的管子,密封的很严。通进一根长铁丝,不觉有堵
-huanhuan2(Winter);
2018-12-27
(#11856141@0)
-
图纸
-huanhuan2(Winter);
2018-12-27
{119}
(#11856152@0)
-
爐子的LED燈是怎麼閃的, 還有你的爐子的型號, 發上來看下. 你檢查下私信你發的第2張圖就是燈狀態對應的故障, 你看下燈狀態對應的是哪個
-seaboy998(seaboy);
2018-12-27
{59}
(#11856294@0)
+1
-
都对不上。打开下门,按住开关,先红一下,后绿,再闪绿。这时不启动,必须关上门才进入启动-停止循环,但这时看不见灯了。从火炉小窗,可看到红光随着启-停,亮-灭。
-huanhuan2(Winter);
2018-12-27
{40}
(#11856299@0)
-
你的炉子上难道没有关于灯的status 说明吗?为什么不认真读一读,说清楚是什么问题?或直接打电话,自己解决不了,挨宰就认了呗,否则后果更坏。
-ontario_2014(rolian);
2018-12-27
(#11856309@0)
-
有说明,什么色灯,亮几下,但症状都对不上
-huanhuan2(Winter);
2018-12-27
(#11856596@0)
-
看下這個視頻
-seaboy998(seaboy);
2018-12-27
{126}
(#11856306@0)
-
看一下這個視頻, 希望對你有幫助
-seaboy998(seaboy);
2018-12-27
{126}
(#11856016@0)
-
对照视频,找不到那几个东西
-huanhuan2(Winter);
2018-12-27
{238}
(#11856135@0)
-
好像是煤气阀没有打开,首先确定家里管道有煤气?,第二,在煤气管道有个电磁阀,听听在启动时,有没有滴答的声音,可以用小螺丝刀敲一敲。。。
-ballfan(BALLFANS);
2018-12-27
(#11856165@0)
-
热水炉有热水,说明家里管道有煤气。启动时有滴答的声音,从火炉小玻璃窗上可以看到里面有通红的光,当然很快就灭了
-huanhuan2(Winter);
2018-12-27
(#11856208@0)
-
就是说已经煤气开始燃烧了?。。。那就很可能是thermal couple 的问题。。。
-ballfan(BALLFANS);
2018-12-27
{39}
(#11856243@0)
-
是点火灯丝的光吧! 而且这炉子哪有什么热电偶。
-cocnut(cocnut);
2018-12-27
(#11856275@0)
-
像石英管一样的东西发光,但启动-停止,亮-灭。炉子是YORK高效炉,有十年了。AIRE ONE买的,过了保修,不知call 他们要多少钱?
-huanhuan2(Winter);
2018-12-27
(#11856291@0)
-
到底煤气燃烧的火光,还是点火器的火光?。。。如果是点火器的火光,那就是煤气阀没有打开。。。
-ballfan(BALLFANS);
2018-12-27
{46}
(#11856318@0)
-
到昨天晚上一直工作好好的,煤气阀肯定没人关。亮光也不是烧煤气的光,是象石英灯一样。
-huanhuan2(Winter);
2018-12-27
(#11856346@0)
+1
-
我说的煤气阀是电动控制的,通过控制板控制的,你的绿灯说明控制ok,就是没有点着煤气,就是阀门没有打开供气,也可能是输出继电器问题。。。
-ballfan(BALLFANS);
2018-12-27
(#11856359@0)
-
这个怎么查?
-huanhuan2(Winter);
2018-12-28
(#11857480@0)
-
先找到继电器,就是有出线连接到阀的那个,在炉子启动时,测量输入电压 如果有输入没有输出则是继电器坏了,如果没有输入,就是板子前级控制问题。。。先把原来的温控器接回去试一试,也许就ok了。。。
-ballfan(BALLFANS);
2018-12-28
{46}
(#11857609@0)
-
昨晚那个师傅用电表测过,说没问题。问题可能是电脑板,要换。。。
-huanhuan2(Winter);
2018-12-28
(#11857674@0)
-
继电器坏蛋可能性极小, 这也不是大功率继电器,查 别的吧
-yuanfanback(归来的远帆);
2018-12-29
(#11858453@0)
-
你知道什么叫大功率继电器?小的继电器就不会坏了吗?。。。
-ballfan(BALLFANS);
2018-12-29
(#11858666@0)
+3
-
我一个装修民工那能知道这些高深的东西啊, 你就行行好,帮网友解决问题, 我一个打酱油的只会凑热闹, 对不起了, 我这是孔夫子门前卖字画, 关公马前耍大刀, 得罪了,
-yuanfanback(归来的远帆);
2018-12-29
(#11859183@0)
-
大侠息怒,大家都是帮我,各有所长,别伤和气。谢过谢过。
-huanhuan2(Winter);
2018-12-29
(#11859379@0)
-
我还会说这句话勒,反正查不出毛病就是用最后一招杀手锏- ------- 电路板坏了, 那不是废话吗, 这些零件哪个不在电路板上? 干脆说, 炉子坏了更好些.
-yuanfanback(归来的远帆);
2018-12-29
(#11858456@0)
-
大侠你支支招啊?!
-huanhuan2(Winter);
2018-12-29
(#11858657@0)
-
问题解决不了了,看谁都是大侠。。。你自己已经乱了,还是继续找那个给你看过的师傅吧,感觉还是蛮诚实的。。。
-ballfan(BALLFANS);
2018-12-29
{70}
(#11858684@0)
+1
-
那个就算了,你没听他忽悠,海吹的时间比他检测的时间多十倍。什么加拿大第一人进口大理石,所有零售,加工厂都从他那儿进货。加拿大唯一一个精通各种电器。。。唉,年纪大了,重操作旧业--维修电器,“屈尊"来给我修火炉,只收个车马费。。。咱可供不起。
-huanhuan2(Winter);
2018-12-29
{163}
(#11859369@0)
-
补充一下:有输入,没有输出,继电器坏 或者 控制信号没有
-hbwang(nick);
2018-12-31
(#11861856@0)
-
你真确认没热电偶?火苗怎么检测的呢?
-ontario_2014(rolian);
2018-12-27
(#11856304@0)
-
他连怎么判断fuse都不知道,这个就更复杂了。。。
-ballfan(BALLFANS);
2018-12-27
(#11856316@0)
-
他这要是不知道没关系,但不能误导别人。
-ontario_2014(rolian);
2018-12-27
(#11856319@0)
-
把下面的门打开,集成板有显示Status的LED灯,一闪一闪绿色,打开门后,即使按住触碰开关,火炉完全不启动
-huanhuan2(Winter);
2018-12-27
(#11856144@0)
-
从你提供的闪灯码,显绿灯应该是正常运行。这与你说的现象有点矛盾。
-cocnut(cocnut);
2018-12-27
(#11856285@0)
-
现象是短暂启动,立马停止,反复。关掉后,有一阵送风。
-huanhuan2(Winter);
2018-12-27
(#11856296@0)
-
前边有说过的可能性大: 点火器坏了。拔下来用一张美元轻轻擦擦看。
-hnryll(松树);
2018-12-27
(#11856300@0)
-
点火器是不是封在亮光的小盒子里,要拆开才看得到?
-huanhuan2(Winter);
2018-12-27
(#11856308@0)
-
看看这个接近你的情况。 1 分钟后边
-hnryll(松树);
2018-12-27
{186}
(#11856340@0)
-
对了,纠正一下,这里说的是传感器。
-hnryll(松树);
2018-12-27
(#11856369@0)
-
找到那个传感器,拆下来,擦了擦,装回去,还是不行。要不要用砂纸打磨?
-huanhuan2(Winter);
2018-12-27
(#11856401@0)
-
就是这个,有点锈,不很赃
-huanhuan2(Winter);
2018-12-27
{119}
(#11856436@0)
+1
-
你现在需要确定煤气有没有燃烧,然后才能确定问题,这是很重要的点。。。视频里面的煤气已经燃烧了。。。
-ballfan(BALLFANS);
2018-12-27
{30}
(#11856455@0)
-
确定煤气没有燃烧
-huanhuan2(Winter);
2018-12-27
(#11856499@0)
-
那就不是sensor问题。。。
-ballfan(BALLFANS);
2018-12-27
(#11856545@0)
-
看来点火器的可能性大,视频1分钟说的传感器,后边说到点火器的,根据你的炉子牌号找点火器,形状很多样,就是通电发红点燃煤气的东东。
-hnryll(松树);
2018-12-27
(#11856557@0)
-
点火器是封在小铁盒里,煤气管通到里面燃烧。密封不好CO会泄漏。对吧?
-huanhuan2(Winter);
2018-12-27
(#11856622@0)
-
点火器是一个“铁丝”一样的电阻,加电就会发热、烧红。
-hunhunhunhun(不知道);
2018-12-27
(#11856650@0)
-
呵呵,如果完全密封了,那外面的空气氧气也就进不去了,没氧气如何燃烧呢?中学物理忘了.....
-see1see(Isee);
2018-12-28
(#11857265@0)
-
进气管送进去的
-huanhuan2(Winter);
2018-12-28
(#11857424@0)
-
那得有气阀控制能进不能出才行,否则外面气体能进去CO也就能出来....
-see1see(Isee);
2018-12-28
(#11857689@0)
-
炉子修好了吗?
-cocnut(cocnut);
2018-12-27
(#11856745@0)
-
问题都没找到,感觉问题很大
-huanhuan2(Winter);
2018-12-27
(#11856798@0)
-
我反而觉得问题不大,但没找到原因罢了。还有,你检查LED灯,应该不用打开炉子面板,有个小孔直接看到状态的,怎么会全盖住了呢?
-ontario_2014(rolian);
2018-12-28
(#11857278@0)
-
小孔是上面观察点火部分,下面门关上才工作,不关上,即使手按住触碰开关,也完全不工作。门关上,看不见灯
-huanhuan2(Winter);
2018-12-28
(#11857426@0)
-
仔细看,一下红光,表示low flame sensor current. 是不是那个传感器还需要打磨下?除锈?
-huanhuan2(Winter);
2018-12-28
(#11857549@0)
-
我也觉得问题不应该大,但。。。主要是希望问题不要大
-huanhuan2(Winter);
2018-12-28
(#11857483@0)
-
“不停尝试点火”说明没有气,检查与气相关的部分
-piston(jim);
2018-12-27
(#11856753@0)
-
气的部分都是铁管,和电磁开关,可动的部分没有
-huanhuan2(Winter);
2018-12-28
(#11857428@0)
-
对, 要么没 天然气,要么氧气不足。点火没问题
-londonsate(lon);
2018-12-31
(#11861232@0)
-
今日工作小节:花钱请了个老师傅,结果出人意料他检查了上面点火器,量了电压,下面排水管,样样都是好的。问题出现在下面电脑板,因为装了Ecobee的无线装置(一个小盒子)从电脑板取电,负载大了,造成电脑板失灵。换个电脑板上千刀。他建议换回老的温控器(GreenOn已经收走了),如果不工作,只能换新电脑板并取消Ecobee. 总感觉哪里不对?!
-huanhuan2(Winter);
2018-12-27
{274}
(#11856760@0)
-
今年GreenOn免费发了好多EcoBee, 大家都有问题吗?
-huanhuan2(Winter);
2018-12-27
(#11856762@0)
+1
-
怪不得你说不出故障码,原来是过程回放 :) 不过得感谢经验分享
-cocnut(cocnut);
2018-12-27
(#11856775@0)
-
没有故障码啊
-huanhuan2(Winter);
2018-12-27
(#11856799@0)
-
1。会不会问题与EcoBee的温控器有关?!
-huanhuan2(Winter);
2018-12-27
(#11856803@0)
-
2。电路板问题会有上面的症状吗?
-huanhuan2(Winter);
2018-12-27
(#11856806@0)
-
3。真是电路板问题,只能换不能修吗?(此电路板老大个,并不是芯片级的)
-huanhuan2(Winter);
2018-12-27
(#11856812@0)
-
这是行话,一般找不到毛病最后一招就是电路板的问题,一般都能全身而退,如果回去找到毛病,他能解决, 那么你就冤枉换一块电路板, 或许再搭上点零件, 如果找不到毛病, 那就是电路板没找到, 你的这种电路板很难找, 你等着吧, 有消息我立即给你打电话. 就像我们去找工作, 老板根本不用你, 而他却对你说:你先回去等消息, 我们商量一下会通知你, 你能留下你的电话号码吗?......
-yuanfanback(归来的远帆);
2018-12-27
{260}
(#11856952@0)
-
赞经验丰富。。。
-ballfan(BALLFANS);
2018-12-28
(#11857396@0)
+1
-
大侠啥时回多?看我抗不抗的住
-huanhuan2(Winter);
2018-12-28
(#11857465@0)
-
6年前由于空调漏水炉子坏了,
-yuanfanback(归来的远帆);
2018-12-29
{1031}
(#11858487@0)
-
“基本原理都一样, 都是在开机前先启动风机, 如果风机正常,并有风通过风管, 通过传感器告知下一个单位”, 这个可能是我的问题所在,昨天检查发现有根拆线松开,不知道是插E18还是E17还是悬空,有人说这线是通到风机,风机没启动?!
-huanhuan2(Winter);
2018-12-29
(#11858705@0)
-
入戏太深。啥板子要上千块哈。楼主遇到典型的欺诈型技工了。不过我也只有一次炉子经验,某人来了三次未果,每次拿50元上门费。我一气之下网购一个板子自己换上。世界太平了
-bricksonly(鑫);
2018-12-28
(#11857414@0)
-
网购板子多少钱?怎么知道是否匹配?
-huanhuan2(Winter);
2018-12-28
(#11857458@0)
-
自己查型号,拿老板子上的,然后比对一下。美国买比加拿大便宜。不过很多不寄加拿大。
-bricksonly(鑫);
2018-12-28
(#11857875@0)
-
可以寄, 不行就寄到美国边境, 自己开车过去取, 我家魁北克的店就离美国边境不远, 当地人都知道美国边境那边有些商店办这个业务 ,就是在加拿大客户在美国网站上买东西, 直接寄到他们商店, 然后你再过境去取, 付点服务费而已, 这样比直接寄到加拿大便宜
-yuanfanback(归来的远帆);
2018-12-29
(#11858493@0)
-
这是什么时节?这时后他要多少就多少.
-yuanfanback(归来的远帆);
2018-12-29
(#11858489@0)
-
如果是春夏秋还可以等上十天半个月的, 现在难度大些啊(这两天老天已经够宽爱他了)
-guanshui88(约定);
2018-12-29
(#11858565@0)
-
是啊, 这是火急火燎的事情.
-yuanfanback(归来的远帆);
2018-12-29
(#11859190@0)
-
4。这个"师傅"靠谱吗?
-huanhuan2(Winter);
2018-12-27
(#11856814@0)
+1
-
5。如果联系GreenOn关于EcoBee温控器的问题,有用吗?如果联系(是不是该部门都撤了)?
-huanhuan2(Winter);
2018-12-27
(#11856817@0)
-
便宜不能随便占啊,那个玩意有Wi-Fi功能直接将你的信息报道政府(不知是否装了窃听),如果那天网络不好使或认为你的炉子不节能,直接开启自毁功能将炉子报废,,,
-guanshui88(约定);
2018-12-28
(#11857255@0)
+1
-
真能想
-ontario_2014(rolian);
2018-12-28
(#11857274@0)
+4
-
要是白宫就好了
-huanhuan2(Winter);
2018-12-28
(#11857437@0)
-
我家前两个星期也是炉子突然坏了,点不着火,用的也是EcoBee.请了个师傅说即时短路电路板也点不着火,所以最后换了个新炉子。
-happyalways(人往高处走);
2018-12-27
(#11856976@0)
-
看到你的帖子才想来是不是EcoBee的电路板问题。那天我家wifi 关了一晚上,到后半夜炉子就不工作了,不知道是不是电路板负载大烧了
-happyalways(人往高处走);
2018-12-27
(#11856995@0)
-
看来是EcoBee引起的。。。
-huanhuan2(Winter);
2018-12-28
(#11857448@0)
-
Google 到这个类似问题,解决了。仅仅因为连线接触不好
-huanhuan2(Winter);
2018-12-28
(#11857681@0)
+2
-
ecobee问题也就是会烧掉电路板的电源部分,也许可以维修,但是,一般师傅是不会这么麻烦的,但是,从你现在还有灯的状态看,并没有烧毁电源部分,具体的要看情况,如果你懂如何跳线测试炉子,可以试一下。。。
-ballfan(BALLFANS);
2018-12-28
(#11857158@0)
-
那是“师傅”怕麻烦?是他们根本不会,只能瞎掰了..呵呵
-ontario_2014(rolian);
2018-12-28
(#11857276@0)
+1
-
行业保护罢了,换板子可以赚大钱。。。
-ballfan(BALLFANS);
2018-12-28
(#11857560@0)
-
那是师傅跳线测试炉子,说是炉子没问题,就是电路板。走了以后,又打电话说,order电路板不能退,要我先换回老式温控器,如果还不工作,再换电路板。
-huanhuan2(Winter);
2018-12-28
(#11857444@0)
-
这个师傅已经不错了。。。
-ballfan(BALLFANS);
2018-12-28
(#11857558@0)
-
我的好像短路电路板点着火了,但师傅说不能这样用,要换电路板,各家炉子不同,电路板不要买,要上千刀,基本等于换半个炉子
-huanhuan2(Winter);
2018-12-28
(#11857453@0)
-
这是垄断行业,板子本事不贵,但是,人工太贵,如果自己可以买到板子是最好的,可以省一半以上,否则,就伸头吧。。。
-ballfan(BALLFANS);
2018-12-28
(#11857557@0)
-
也没有。。。我自己网上买板子花了100,师傅说他能帮找二手板子,250。那时我穷,就自己买了,家里穿了几天棉衣
-bricksonly(鑫);
2018-12-28
(#11857880@0)
-
师傅说他帮我买个便宜的也要上千,差不多半个火炉的钱。。。
-huanhuan2(Winter);
2018-12-28
(#11857916@0)
-
师傅不就是等你一句“换新”么。酱紫,他的无能得以掩饰,而且修了半天白拿上门费了,还顺带做一单换新的生意
-bricksonly(鑫);
2018-12-28
(#11858254@0)
+2
-
这个师傅还是明白的,ECC Bee的老问题C wire取电,容易造成烧坏板子的原来电源。我两年前有个帖子探讨过这个事儿。。。Eco Bee的C wire很重要,你要确定你的C wire的接法正确,而且,Eco Bee自己本身不带电源和带电源接法不同,自带电源最好加隔离继电器,否则,很可能产生48vac烧板子,好像前面看到哪里有个你测到48V的回帖。。。
-ballfan(BALLFANS);
2019-1-2
{196}
(#11864111@0)
-
进来看看大家集思广益,能不能把这个修好,不过可苦了楼主挨冻。
-zhengsean(IT大叔);
2018-12-28
(#11857223@0)
-
点火时你仔细闻闻看有没有煤气的味道,如果有就是点火器问题,那就试着用打火机点火(需要把炉门打开并按住炉门sensor),如果能点着,炉子正常工作,就赶快去买点火器。
-tzm_oasis(绿洲);
2018-12-28
(#11857231@0)
-
打火机点炉子?这个可是需要点胆量。。。万一回火出来,那可是呵呵。。。
-ballfan(BALLFANS);
2018-12-28
{30}
(#11857354@0)
+1
-
点火时没有煤气的味道,但那是师傅跳线测试炉子,可以点火,说是炉子没问题
-huanhuan2(Winter);
2018-12-28
(#11857446@0)
-
跳线时使用你的点火器还是师傅的?
-tzm_oasis(绿洲);
2018-12-28
(#11857661@0)
-
我的点火器。师傅跳线就是用钳子插进电脑板的哪根线,没有另外的点火器
-huanhuan2(Winter);
2018-12-28
(#11857675@0)
-
点火器大致长这样
-tzm_oasis(绿洲);
2018-12-28
(#11857666@0)
-
看着像昨天我拿出来擦的“传感器”,是一个东西吗?见图
-huanhuan2(Winter);
2018-12-28
{60}
(#11857676@0)
+1
-
这个要不要擦得很干净?没一点锈?
-huanhuan2(Winter);
2018-12-28
(#11857677@0)
-
那个东西叫hot surface ignitor, 不能用手摸的,
-water9(plumbingheatinggas);
2018-12-28
(#11857687@0)
-
感觉是一个东西,见视频
-huanhuan2(Winter);
2018-12-28
{126}
(#11857688@0)
-
你那个叫flame rod,是传感器,
-water9(plumbingheatinggas);
2018-12-28
(#11857694@0)
-
我曾经就是把锈擦掉就好了。
-fxchen(fxc);
2018-12-30
(#11860948@0)
-
你的如果是有pek的,就换个nest或者老式温控器吧。
-tzm_oasis(绿洲);
2018-12-28
(#11857716@0)
+1
-
老式温控器叫GreenOn收走了,当时问他收回去也没用,他说是程序。感情现在坑在这里。。。
-huanhuan2(Winter);
2018-12-28
(#11857778@0)
-
你更生猛, 打火机都能点着炉子?你以为是做饭的煤气炉啊, 现在的炉子好多保护措施, 有一项出了问题都不送煤气, 那个煤气阀是最后的一关, 前面任何一关没过去都不能打通最后一关.
-yuanfanback(归来的远帆);
2018-12-29
(#11859211@0)
-
小时候做饭就这么点炉子,习惯了。我自己的暖炉就这么修的。不过看起来楼主的问题不一样
-tzm_oasis(绿洲);
2018-12-29
(#11859304@0)
-
你的问题是房子太大,走线太长,线上的压降大了。
-cocnut(cocnut);
2018-12-28
(#11857597@0)
-
房子不大,十年没问题,今年换EcoBee, ...
-huanhuan2(Winter);
2018-12-28
(#11857605@0)
-
换了EcoBee后,因它需要电源,这大房子长线问题就暴露出来了
-cocnut(cocnut);
2018-12-28
(#11857610@0)
-
可不可以给它单独电源?有什么解决办法现在?
-huanhuan2(Winter);
2018-12-28
(#11857678@0)
-
换个小房子,炉子也就不需要这么大这么高级了说着玩的。去CT买一个温控器,最便易的电子式的就行。
-cocnut(cocnut);
2018-12-28
{50}
(#11857682@0)
-
仔细检查主板,发现有根插线松了,拔出来后,发现有两个插柱,只有一根线,到底插哪个插柱吗(1 or 2)?见图
-huanhuan2(Winter);
2018-12-28
{60}
(#11857771@0)
-
急等,插错的话,有危险吗?
-huanhuan2(Winter);
2018-12-28
(#11857783@0)
-
将插头边上的字照清楚些,看看这两个插头是干什么的,看样子没什么区别。
-bluesky2000(bluesky2000);
2018-12-28
(#11857784@0)
-
E17 和 E18 (附图纸)
-huanhuan2(Winter);
2018-12-28
{119}
(#11857808@0)
-
这一排都是Neutral,插白线的,都一样。
-bluesky2000(bluesky2000);
2018-12-28
(#11857815@0)
+1
-
确定都一样?插错了会烧主板吗?
-huanhuan2(Winter);
2018-12-28
(#11857890@0)
-
插哪一个都可以,但要确认以前插进去没有
-hbwang(nick);
2018-12-28
(#11857861@0)
-
E18柱顶有点金属糊的痕迹,E18和E17柱侧面都似灰蒙蒙的,没插过的划痕。试着插进E18, 发现没可能插紧,非常容易松。
-huanhuan2(Winter);
2018-12-28
(#11857888@0)
-
教训,下回拔线前先拍照.....
-see1see(Isee);
2018-12-28
(#11857799@0)
+1
-
不是我拔的,一碰是松的,再一拿就下来了,感觉是在E18,想放回去,怕不对。
-huanhuan2(Winter);
2018-12-28
(#11857813@0)
-
碰前、拿之前就得拍....
-see1see(Isee);
2018-12-28
(#11857856@0)
-
仔细靠近看看,那个接头是插上去的,肯定有痕迹的。
-coolrock(coolrock);
2018-12-28
(#11857828@0)
-
都看不出痕迹,好像那根线就放旁边没插过。
-huanhuan2(Winter);
2018-12-28
{119}
(#11857855@0)
-
拿放大镜仔细看看比较一下,没灰尘蒙着,比较干净的那个插柱就是....
-see1see(Isee);
2018-12-28
(#11857858@0)
+1
-
再仔细看,E18柱顶有点金属糊的痕迹,E18和E17柱侧面都似灰蒙蒙的,没插过的划痕。试着插进E18, 发现没可能插紧,非常容易松。
-huanhuan2(Winter);
2018-12-28
(#11857882@0)
-
以前的图片 感觉没有插啊
-hbwang(nick);
2018-12-28
{27}
(#11857835@0)
-
对,好像是没插。因为旁边两个插的,非常非常紧,用力都拔不出来。试着插这一个,不用大力插不进去,上图示,这个插头里面是凹型,插进的话,会卡得很紧的。
-huanhuan2(Winter);
2018-12-28
{179}
(#11857853@0)
-
现在路子还在燃烧吗?师傅短路打火以后
-hbwang(nick);
2018-12-28
(#11857866@0)
-
师傅确认短路能打火,就断掉了,说不能这样用,类似没有回路之类。。。
-huanhuan2(Winter);
2018-12-28
(#11857869@0)
-
短路工作,就说明炉子本身没事,温控器或设置有问题。
-bluesky2000(bluesky2000);
2018-12-28
(#11857897@0)
+1
-
问题出在了控制电路部分,很有可能某个sensor造成控制自动熄火保护。通电的情况下测量各个sensor,或者摘掉各个sensor打火后一个接一个插入进行排查。不只是sensor自身对清洁有要求,sensor旁边也清洁一下。最不幸运的是主板坏,若动手能力强,自己买一个换上也没有多少银子,祝你好运
-hbwang(nick);
2018-12-28
{240}
(#11857873@0)
-
还有一个可能就是ecobee的问题把之前的控制器换上试一下
-hbwang(nick);
2018-12-28
{24}
(#11857889@0)
-
跟EcoBee有关,但问题还没找到
-huanhuan2(Winter);
2018-12-28
(#11857903@0)
-
Ecobee 温控器的连线,如果是四根线,线得连接很特殊。
-bluesky2000(bluesky2000);
2018-12-28
(#11857923@0)
-
你换上以前的温控器试一下啊
-hbwang(nick);
2018-12-28
(#11857929@0)
-
以前的温控器叫GreenOn收走了,当时问他收回去也没用,他说是程序。感情现在坑在这里。。。
-huanhuan2(Winter);
2018-12-28
(#11857935@0)
-
那你把ecobee 拿下来 把里面的风扇和取暖的线和24v短路 看炉子是否启动
-hbwang(nick);
2018-12-28
(#11857958@0)
-
昨晚师傅可以启动,并说火炉是好的,是电脑板坏了。他后来又打电话说不肯定,要换旧的温控器试试。
-huanhuan2(Winter);
2018-12-28
(#11858001@0)
-
查查白线连到哪去了?什么牌子的炉子?
-bluesky2000(bluesky2000);
2018-12-28
(#11857876@0)
-
YORK的高效炉,十年新。附图纸
-huanhuan2(Winter);
2018-12-28
{60}
(#11857886@0)
-
你图纸哪里的 太不清晰了 分段拍
-hbwang(nick);
2018-12-28
(#11857891@0)
-
分段拍图纸
-huanhuan2(Winter);
2018-12-28
{119}
(#11857904@0)
-
2
-huanhuan2(Winter);
2018-12-28
{179}
(#11857905@0)
-
图纸看不太清楚,把型号告诉我,可以上网查。图纸控制板上部的连线表示的零线的连接。
-bluesky2000(bluesky2000);
2018-12-28
(#11857894@0)
-
Unit Model: PV9B12N060UP12B Serial Number: W0D8769326
-huanhuan2(Winter);
2018-12-28
{179}
(#11857899@0)
-
图纸显示零线五个头,1变压器,2加湿器(一般是空),3除尘器(一般是空),4电机,还有一个是总零线,回到电源。顺着空的白线看看连到什么部件上了,再确定需不需要插上。
-bluesky2000(bluesky2000);
2018-12-28
(#11857919@0)
-
顺着空的白线连到火炉侧下方的集线丛,与左边两根白线不同。照片最右边是filter.
-huanhuan2(Winter);
2018-12-28
{60}
(#11857922@0)
-
这一张清楚,图示白线
-huanhuan2(Winter);
2018-12-28
{60}
(#11857927@0)
-
你插进去试一下。你把ecobee 控制器拿下来 把里面的线短路一下 看炉子是否启动
-hbwang(nick);
2018-12-28
(#11857934@0)
-
插进去主板不会烧吧?!
-huanhuan2(Winter);
2018-12-28
(#11857936@0)
-
我的意思是插E18还是E17柱?
-huanhuan2(Winter);
2018-12-28
(#11857938@0)
-
不会烧主板 应该风机的线
-hbwang(nick);
2018-12-28
(#11857954@0)
-
都可以 1718电路板都是连一起的
-hbwang(nick);
2018-12-28
(#11857955@0)
-
插上了(E18), 还是老样子(启动-停止),注意到先绿光,橙光,再红光,再灭。
-huanhuan2(Winter);
2018-12-28
(#11857964@0)
-
要看控制板上的灯。
-bluesky2000(bluesky2000);
2018-12-28
(#11857966@0)
-
这种不同颜色和闪烁的顺序本身可能就是一种error code,你查手册或资料应该就知道是属于什么问题,再根据提示去做.....
-see1see(Isee);
2018-12-28
(#11857969@0)
-
这里是Code, Rapid Amber: Low flame sense current; Steady On Red: Control failure; 1 Red: Flame present with gas off.
-huanhuan2(Winter);
2018-12-28
{60}
(#11857974@0)
-
你的情况对应哪个Code?
-bluesky2000(bluesky2000);
2018-12-28
(#11857986@0)
-
再次检查确认一下有关连线有无问题,还有开关,比如煤气开关,如果开关失灵看似开着其实已经关闭,不妨来回拧几下....
-see1see(Isee);
2018-12-28
(#11857989@0)
-
如果有一根粗的白线连到了电机,这根线应该不接到Natural上,就应该悬空。
-bluesky2000(bluesky2000);
2018-12-28
(#11857956@0)
-
我把它拔下来悬空,结果一样。要不要插E17试试?
-huanhuan2(Winter);
2018-12-28
(#11857970@0)
-
如果有万用电表的话,在悬空情况下带电测测线头的电压,按理电压/电流值比较高且对电路板有重大影响的接头应该连接比较牢靠,不会这么容易扯下来的,要是俺就插上试试,没啥大不了的...
-see1see(Isee);
2018-12-28
(#11857979@0)
-
你现在思路是不是偏了,师傅短路炉子正常,为啥还在研究炉子。ecobee换了不就可以吗,去买个温控器
-hbwang(nick);
2018-12-28
(#11857981@0)
-
这个是正路子。
-bluesky2000(bluesky2000);
2018-12-28
(#11857988@0)
-
也是,反正现在就是死马当活马来医,若能记得原来的温控器牌子型号,去买个一模一样的回来装上试试,但愿装Ecobee时没改过线路,不然还得折腾....
-see1see(Isee);
2018-12-28
(#11857995@0)
-
不知道你如何知道“火炉不停尝试点火,但起不来”----把小门拿开,看看清楚在说下一步。点火是烧红的电阻;如果点火的烧红了,送气的阀门澎一声响开启了---那就是没有气出来。如果没有送气的声音,那是送气的线路问题。
-hunhunhunhun(不知道);
2018-12-28
(#11857975@0)
-
有滴答的声音,没有送气的声音。
-huanhuan2(Winter);
2018-12-28
(#11857980@0)
-
跳过温度控制器,把接线直接连接几秒钟,看看能不能启动。
-hunhunhunhun(不知道);
2018-12-28
(#11857984@0)
-
昨晚师傅可以启动,并说火炉是好的,是电脑板坏了。他后来又打电话说不肯定,要换旧的温控器试试。
-huanhuan2(Winter);
2018-12-28
(#11857997@0)
-
不需要旧的,随便买一个24v的温控器就可以
-hbwang(nick);
2018-12-28
(#11858007@0)
-
估计是ecobee温控电路板出了问题,虽然是免费的,也可以退换。直接找厂家就可以换。在温控器那个地方短路若炉子正常启动就确认问题在哪里
-hbwang(nick);
2018-12-28
(#11858010@0)
-
炉子能启动,就是炉子(包括控制板)是好的,问题出在外部控制的温控器。
-bluesky2000(bluesky2000);
2018-12-28
(#11858013@0)
-
拆下了温控器,还是老问题
-huanhuan2(Winter);
2018-12-28
(#11858062@0)
-
那一定有ErrorCode,读一下是什么?
-bluesky2000(bluesky2000);
2018-12-28
{62}
(#11858139@0)
-
先绿光,橙光,再红光,再灭。
-huanhuan2(Winter);
2018-12-28
(#11858156@0)
-
刚给EcoBee Support打了电话,按他的指示,拆下了PEK小白盒子,然后红线和白线相连,仍然是老问题。他就说不是EcoBee问题。
-huanhuan2(Winter);
2018-12-28
(#11858061@0)
-
炉子主板r w短路 炉子启动不了?
-hbwang(nick);
2018-12-28
{57}
(#11858101@0)
-
这个EcoBee的小白盒子拆下来了,四根线接回主板。我不知道怎么做主板r w 短路。是有楼上EcoBee温控器处做处r w 短路,火炉子启动不了。
-huanhuan2(Winter);
2018-12-28
{298}
(#11858138@0)
-
不需要拆 小白盒子后面的线 rw短路就可以
-hbwang(nick);
2018-12-28
(#11858144@0)
-
小白盒子后面的线直接接主板上了,rw短路是在温控器上(见图)。主板上如何rw短路?
-huanhuan2(Winter);
2018-12-28
{119}
(#11858150@0)
-
u型电线 镊子 一头接主板r 一头主板w
-hbwang(nick);
2018-12-28
(#11858186@0)
-
师傅拿个钳子,伸进去短路,不知道是哪两个。是不是只要R - W 连接上就是短路了?
-huanhuan2(Winter);
2018-12-28
(#11858249@0)
-
对
-hbwang(nick);
2018-12-28
(#11858252@0)
-
排查问题越简单越好,这样才能找到问题
-hbwang(nick);
2018-12-28
(#11858208@0)
-
线 测过吗?电压多少
-hbwang(nick);
2018-12-28
(#11858146@0)
-
昨晚师傅量过说OK, 我不懂量哪根线
-huanhuan2(Winter);
2018-12-28
(#11858152@0)
-
你量一下C和RH,C-RC的电压,如果是两个变压器都应该有24vAC,或者只有一个应该短接在一起。
-hunhunhunhun(不知道);
2018-12-28
(#11858167@0)
-
你的线接错了。
-bluesky2000(bluesky2000);
2018-12-28
(#11858149@0)
-
哪根错了?
-huanhuan2(Winter);
2018-12-28
(#11858153@0)
-
最后一张照片的线是错的。
-bluesky2000(bluesky2000);
2018-12-28
(#11858157@0)
-
我知道你的意思,那张照片不清楚,看这张
-huanhuan2(Winter);
2018-12-28
{72}
(#11858166@0)
-
两个黑线应该连在Y上,而不是C。
-bluesky2000(bluesky2000);
2018-12-28
(#11858175@0)
-
EcoBee Support 说连C, 温控器处也连的C. 后来发照片给他确认的
-huanhuan2(Winter);
2018-12-28
(#11858185@0)
-
有可能,4黑色线室外的压缩机继电器的零线。
-hunhunhunhun(不知道);
2018-12-28
(#11858195@0)
-
这个照片只有5个连线:R(24Vac+), G(风扇),W(暖气),Y(室外空调压缩机),C就是common零线(N线)。
-hunhunhunhun(不知道);
2018-12-28
(#11858181@0)
-
你用Ecobee的转换盒时需要连接C,直接短路时已经跨过了温控器,你现在的接法是错的。
-bluesky2000(bluesky2000);
2018-12-28
(#11858192@0)
-
短路是在温控器,不在主板,看这照片你就明白
-huanhuan2(Winter);
2018-12-28
{60}
(#11858216@0)
-
很简单的4条线控制:1。电源线R(24V),2零线 C. 3。暖气开W。4。空调开Y。如果W(暖气)有24V,暖气就开启了。
-hunhunhunhun(不知道);
2018-12-28
(#11858272@0)
-
你哪个4#黑线啥意思?
-hunhunhunhun(不知道);
2018-12-28
(#11858188@0)
-
有两组线,照片看重叠了不清楚,有标号的1(W),2(R),3(G),4(C)是拆掉小白盒后接回主板的线。没标号的另一组线是Y1(黑)C(白)。
-huanhuan2(Winter);
2018-12-28
(#11858204@0)
-
4(C ) 接错了,应该在Y上。另一组Y1(黑)也应该在Y上。这是对于通用的的温控器。现在是Ecbee,而且你只有四条线,所以加了个转换盒。转换盒到控制板要连接C,从温控器到转换盒没有C。只能在Ecobee的温控器处重新连接,到Pek, Rc等。
-bluesky2000(bluesky2000);
2018-12-28
(#11858222@0)
-
EcoBee Support要我把黑线从PEK拔下,接到G.
-huanhuan2(Winter);
2018-12-28
{60}
(#11858242@0)
-
G是控制风扇的。如果你是在暖气那档,不管你设置在auto 还是ON,点火以后自己就开了。
-hunhunhunhun(不知道);
2018-12-28
(#11858264@0)
-
这样简单点吧。在炉子那,关掉电源,拆掉这些连接线,记得照张照片做记录。用一根短线将R-W短接。打开电源,用手按住炉子门上的开关,看看炉子启动不启动,如果不启动是什么ErrorCode. 这是炉子Service的杀手锏了。
-bluesky2000(bluesky2000);
2018-12-28
(#11858266@0)
-
用钳子短接R-W, 启动不了,先红灯,后橙灯
-huanhuan2(Winter);
2018-12-28
(#11858279@0)
-
一定用线,让炉子有时间完成整个循环,才能不断闪灯。
-bluesky2000(bluesky2000);
2018-12-28
(#11858281@0)
-
用钳子按住,也是启动-停止,摘了几下,跟以前一样,试了接上E18和不接都一样
-huanhuan2(Winter);
2018-12-28
(#11858297@0)
+1
-
开门短路时要按住开门开关
-hbwang(nick);
2018-12-28
(#11858300@0)
-
用线短接,这样子你才可以有时间看到炉子是啥状态。1。点火那东西烧红没有?如果这一步都没有走到,就是排气开关那里没有闭合。2。点火器烧红后天然气阀门就会开启,澎的一下,火就起来了。
-hunhunhunhun(不知道);
2018-12-28
(#11858319@0)
-
开门短路按开门开关,否则没电。炉子沒点火,只有滴答声,(昨晚师傅确实点着火了,看到里面通红)。有可能是拆掉EcoBee, 重新接线有问题,还有个疑点是E18还是E17还是悬空?
-huanhuan2(Winter);
2018-12-28
(#11858349@0)
-
3。火点起来没有?或者点着后几秒钟又熄灭了。如果熄灭了,那就是楼上说的检测燃烧温度的热电偶那里的问题。
-hunhunhunhun(不知道);
2018-12-28
(#11858320@0)
-
火沒点起来,嘀答声就没了
-huanhuan2(Winter);
2018-12-28
(#11858350@0)
-
控制板上显示的FaultCodes是什么呢?
-bluesky2000(bluesky2000);
2018-12-28
{62}
(#11858310@0)
-
其实我一直觉得他没有找到正确的Code, 应该关上门或按住们的开关,总之必须让炉子认为在正常条件下出现的fault code 才行,否则没法正确的diagnostic.
-ontario_2014(rolian);
2018-12-28
(#11858330@0)
-
没有控制板显示,可能十年前炉子沒有。读code点能从状态灯颜色和闪数判断。最近短路信号是红一橙
-huanhuan2(Winter);
2018-12-28
(#11858352@0)
-
他说过了“启动时有滴答的声音,从火炉小玻璃窗上可以看到里面有通红的光,当然很快就灭了”----估计是温度检测电偶得问题。可以检查一下电阻。
-hunhunhunhun(不知道);
2018-12-28
(#11858331@0)
-
不是火炉小玻璃窗(那是师傅点着火看的),是下门小孔看L E D灯光启一停时
-huanhuan2(Winter);
2018-12-28
(#11858354@0)
-
你这样麻烦?先量一下R--C有没有24V?开到暖气就是 R--连接--W。你去炉子接线那里去测试,把温度控制器分离开,排除这些线可能连接错误。
-hunhunhunhun(不知道);
2018-12-28
(#11858155@0)
-
是用这一档量直流24V吗?
-huanhuan2(Winter);
2018-12-28
{60}
(#11858179@0)
-
这是直流,用交流哪个档,后面带波浪的。
-hunhunhunhun(不知道);
2018-12-28
(#11858183@0)
-
交流电?
-hbwang(nick);
2018-12-28
(#11858189@0)
-
是,V~, 200那里。24V,不会电死你的。
-hunhunhunhun(不知道);
2018-12-28
(#11858198@0)
-
是量的交流电,R--C有27.6V
-huanhuan2(Winter);
2018-12-28
(#11858207@0)
-
现在你可以做的就是,把电路板上的W 拔掉,用一条线短接R(24V)---和 W,这样子等于替代了温度控制器。看看如何,如果工作的话,你买一个新的温度控制器装上去。(你现在量一下W-C的电压,应该是没有的)
-hunhunhunhun(不知道);
2018-12-28
(#11858260@0)
-
用钳子短接R-W, 启动不了,先红灯,后橙灯
-huanhuan2(Winter);
2018-12-28
(#11858275@0)
-
师傅短路后运行了多长时间?
-hbwang(nick);
2018-12-28
(#11858328@0)
-
半分钟的样子,我以为可以供暖了,他说不能这样工作,只是测试都是好的
-huanhuan2(Winter);
2018-12-28
(#11858357@0)
-
R--C有27.6V
-huanhuan2(Winter);
2018-12-28
(#11858197@0)
-
你量rw多少
-hbwang(nick);
2018-12-28
(#11858213@0)
-
R--W有27.7V
-huanhuan2(Winter);
2018-12-28
(#11858221@0)
-
你是从温控器那边测量的吗?
-hbwang(nick);
2018-12-28
(#11858255@0)
-
不是,直接从主板量的
-huanhuan2(Winter);
2018-12-28
(#11858261@0)
-
从温控器那头测量一下电压
-hbwang(nick);
2018-12-28
(#11858302@0)
-
看看这个视频把,很有可能是这个问题。furnace thermocouple 是控制天然气开关的,如果没有温度,电磁阀就会关闭。
-hunhunhunhun(不知道);
2018-12-28
{267}
(#11858345@0)
-
这种炉子已经好老了, 还是火种点火的, 现在都什么朝代了, 现在的炉子比它先进好多, 问题也更难处理.
-yuanfanback(归来的远帆);
2018-12-29
(#11859239@0)
-
是,看看这个,感觉是网上最好的
-hunhunhunhun(不知道);
2018-12-29
(#11859240@0)
-
可怜啊,还冻着呢。就不能找个靠谱点的师傅一下子解决了…
-wabuka(waka);
2018-12-29
(#11858366@0)
+1
-
熟话说 “可怜之人必有,,,,”
-guanshui88(约定);
2018-12-29
(#11858562@0)
-
可恨啊,工作出了问题,这几天连轴加班给人擦屁股,又遇到这事儿,找了个“师傅”花钱花时间,还在受冻,我招谁了?!
-huanhuan2(Winter);
2018-12-29
(#11858725@0)
-
打电话给enercare,问下看看加Heating Protection Plan和不加plan各是什么价格,他们应该肯定能弄好的。
-xjcjq(rufeng);
2018-12-29
(#11858741@0)
-
Enercare: $129 per hour + parts for repairs
-huanhuan2(Winter);
2018-12-29
(#11858752@0)
-
你问下加Protection Plan后是什么价格,记得他们是加计划后超过十天报修没有额外收费,十天之内要加收一些费用。当然维修总金额和部件还有一些其他的限制。
-xjcjq(rufeng);
2018-12-29
(#11858788@0)
-
我家是有他家计划的,去年最冷的时候炉子停摆,报修以后来人检查换了马达,完全免费,修的人说没计划的话大概要三百多。
-xjcjq(rufeng);
2018-12-29
(#11858798@0)
-
他说买了计划,只Cover头五百费用,超过要付
-huanhuan2(Winter);
2018-12-29
(#11858947@0)
-
刚打电话叫了个国人,说可能是压力开关有问题(或堵了或坏了),来一趟检查收80, 如果问题简单,当场解决。如果要换零件,有旧的就换上解决问题,没有的话,等周一Dealer上班,报销零件,外加30油费。可以吗?
-huanhuan2(Winter);
2018-12-29
(#11858810@0)
-
他说的压力开关是在哪里堵?
-huanhuan2(Winter);
2018-12-29
(#11858817@0)
-
哪个是排气的 inducer motor,排气到外面,如果工作正常(通向外墙的气路没有堵住),有个开关就会吸合。
-hunhunhunhun(不知道);
2018-12-29
(#11858956@0)
-
是这个马达连接的粗白管吗?我把两个小黄賵拧下来,打气筒打气,好像是通的,至少通到外面就不知怎么测?
-huanhuan2(Winter);
2018-12-29
{119}
(#11858973@0)
-
是,那个马达一转就会吸和一个开关---〉到下一步,点火器。只要你开启了暖气R-W连接,这个马达就会立即旋转。如果没有转起来,那就是不正常。
-hunhunhunhun(不知道);
2018-12-29
(#11858982@0)
-
短路R-W, 这个马达启动后,马上停止。是风管堵了还是马达坏了(马达可以启动转动)?
-huanhuan2(Winter);
2018-12-29
(#11858988@0)
-
这时LED灯的状态?
-ontario_2014(rolian);
2018-12-29
(#11859015@0)
-
红灯短亮(不是闪);橙灯短亮,电机(见图)启,停
-huanhuan2(Winter);
2018-12-29
(#11859060@0)
-
如果红灯是亮一下就灭代表“flame present with gas off". 橙灯持续快闪代表”low flame sense current". 橙灯闪三下代表“w2 present without w1 call”。 橙灯闪四下代表“y present without g call"
-tzm_oasis(绿洲);
2018-12-29
(#11859187@0)
-
红灯亮一下,橙灯亮一下,马达启,停,一个循环不到十秒。
-huanhuan2(Winter);
2018-12-29
(#11859200@0)
-
测量电压啊!!!就是马达的电压AC 200档。如果电压一直有,而马达不转,问题是马达这里。tip: 关掉电源把连线一个个拔下来检查再插回去。
-hunhunhunhun(不知道);
2018-12-29
(#11859018@0)
-
我感觉不是电机坏了,是由于某个反馈信号没满足条件的保护,也就是常说的interlock,应该去找这时的LED所对应的故障。
-ontario_2014(rolian);
2018-12-29
(#11859030@0)
-
所以才让你测量电压:如果没有了电压马达不旋转那是前面控制的问题。如果一直有电压,马达不转就是马达的问题。判断这些,不能靠猜测。你自己看看ladder digram哪个图。
-hunhunhunhun(不知道);
2018-12-29
(#11859038@0)
-
每次启-停,马达都能转,马达应该没问题。你说的前面控制是不是电路板问题,即没有电压?
-huanhuan2(Winter);
2018-12-29
(#11859063@0)
-
你量过电压了吗?如果马达阻力很大,马达会自我保护的,防止火灾。马达上面的白色排气管到室外不能堵住,有些安装不好,水进去结冰就堵住了。
-hunhunhunhun(不知道);
2018-12-29
(#11859080@0)
-
去外面的排气管看了,朝里面吹气,好像没堵。没量电压,不知怎么量?
-huanhuan2(Winter);
2018-12-29
(#11859123@0)
-
电压都不会量?先关掉电源,把表笔插到两条线接头上。。。看看这个从7分钟开始。
-hunhunhunhun(不知道);
2018-12-29
{126}
(#11859172@0)
-
你做这些检查前,要把门上的开关用胶布粘起来,否则门开了一切都切断了。
-hunhunhunhun(不知道);
2018-12-29
(#11859098@0)
-
新师傅来了,检查(短路)一下,说主板坏了,上面有个吸合开关“吸”不住。这是新型板,换一个要200-300.然后叫助理去拿电表,开始量电压,不说话了...
-huanhuan2(Winter);
2018-12-29
{43}
(#11859196@0)
-
听着靠谱点,公布一下名字,看是不是有劣迹的
-tzm_oasis(绿洲);
2018-12-29
(#11859273@0)
-
才开始折腾。。。维修不带万用表。
-hunhunhunhun(不知道);
2018-12-29
(#11859296@0)
+1
-
那种带钳子的万用表(还没电池了,问我要电池),跟上面视频里的一样,估计钳子接地线方便。我给他我的万用表,他说不行。
-huanhuan2(Winter);
2018-12-29
(#11859451@0)
-
一个群友介绍的,他家的两个炉子都是他做的
-huanhuan2(Winter);
2018-12-29
(#11859441@0)
+1
-
接上回书,师傅闷头鼓捣一会儿,把风机启动了,但是打不着火。这才果断地说:换主板。 问大概多少银子,曰两到三百两,并说这种DC的板子不好找。Dealer周一才上班,回家看看有没有旧的可换上。遂呈上八十大洋,辛苦了。今日战况毕。
-huanhuan2(Winter);
2018-12-29
{143}
(#11859352@0)
-
DC 板子?又遇到一个骗子。他来了帮你检测了些啥?
-hunhunhunhun(不知道);
2018-12-29
(#11859407@0)
-
主板R-W短路,这三天我做了无数回。然后用短线(连啥我不知道),直接启动了风机,但打不着火。我问要不要先检查点火器,他说点火器是个小东西,要换很容易,他车上现在就有。按流程,主板要给信号,但没有。所以要换主板先。
-huanhuan2(Winter);
2018-12-29
(#11859447@0)
-
“飞人”网友不是告诉你如何检测鼓风扇了吗?直接R-G就可以。inducer motor马达不转(就是那个开关不吸合),主板是不会送出点火电压的。他有没有测量点火器有没有 120V电压? 你需要一步步地判断。
-hunhunhunhun(不知道);
2018-12-29
(#11859456@0)
-
里面很窄,只能他一个人在里面,具体干啥看不到。知道的就问下而已。我已精疲力尽,明天还要加班。花钱买平安吧。谢谢大伙热心帮助,术业有专攻。
-huanhuan2(Winter);
2018-12-29
{72}
(#11859514@0)
-
你把这个视频仔细看一便,看明白,完全可以找到问题。
-hunhunhunhun(不知道);
2018-12-29
{126}
(#11859464@0)
-
你现在测试结果和你说的不同,你以前说的是“可以启动,但是一直在澎澎开气阀。”,现在短截没有反应,可能是尝试3次后,炉子被锁住了。或者等一个小时,或者断电消除记忆。如果能点火启动,但是会熄灭,需要量一下flame sensor的电流,一般5微安左右,小的话会被认为‘没有火。
-hunhunhunhun(不知道);
2018-12-29
{230}
(#11858611@0)
-
这样下去估计你自己不会挨冻,但墙里的水管会有问题,如果自己不成,还得找人啊……
-ontario_2014(rolian);
2018-12-29
(#11858639@0)
-
找人ing...Aire One: $100 for visit; Enercare: $129 per hour + parts for repairs
Furnace Toronto: $80 for diagnostics ($20 coupon used)
-huanhuan2(Winter);
2018-12-29
(#11858714@0)
-
你要不要试试Honeywell Multi pro7000,TB7100A1000的温控器,把白色的小盒子取下?
-jimli6(jimli6);
2018-12-29
(#11858791@0)
-
已经把EcoBee温控器拆了,直接短路,也启动不了
-huanhuan2(Winter);
2018-12-29
(#11858814@0)
-
你学师傅的样子jump wire不久行了吗?
-tzm_oasis(绿洲);
2018-12-29
(#11859151@0)
-
学师傅是用钳子,短路 R-W
-huanhuan2(Winter);
2018-12-29
(#11859203@0)
-
开门短路时要按住开门开关 -hbwang(nick);
-tzm_oasis(绿洲);
2018-12-29
(#11859260@0)
-
当然了,否则没电
-huanhuan2(Winter);
2018-12-29
(#11859437@0)
-
follow error code retrieval, 你得到什么?
-tzm_oasis(绿洲);
2018-12-29
(#11859268@0)
-
红灯短亮(不是闪);橙灯短亮,电机启,停
-huanhuan2(Winter);
2018-12-29
(#11859439@0)
-
都几天了。家里还没暖气,你太太脾气真好。
-dashixiong(nonono);
2018-12-29
(#11859472@0)
+1
-
老天佑我,不算太冷。没想到今年最后几天,弄的焦头烂额,挺住,明年会更好!
-huanhuan2(Winter);
2018-12-29
{12}
(#11859527@0)
-
花钱维修或者买一个新的,要讲究生活质量
-dashixiong(nonono);
2018-12-29
(#11859528@0)
+1
-
是啊,今天这个师傅,带个助理,看着还靠谱,看他今明两天搞不搞惦其实这三天我都在上班,工作开会都没耽误,能挤出时间码这么多,不该受赞吗?!
-huanhuan2(Winter);
2018-12-29
{74}
(#11859538@0)
-
对家人不负责啊,我家暖气坏的时候,几小时马上修好,再贵也要修,老少都冻不起
-dashixiong(nonono);
2018-12-29
(#11859575@0)
+1
-
工作不过是为了别人的财务报表上添几个数而已,优先级应该是最低的。
-wangmin88666(wangmin);
2018-12-30
(#11860009@0)
+2
-
看来应该是负压建立不起来。
-jetman(飞人);
2018-12-30
{162}
(#11859805@0)
-
这人很专业,看哪个测试表就知道。LZ遇到不懂维修的“专业人士”,挨冻。
-hunhunhunhun(不知道);
2018-12-30
(#11859922@0)
-
看这个视频捅进去很深,我的只有20cm,里面很硬,捅不进去。应该有多深?
-huanhuan2(Winter);
2018-12-30
(#11860600@0)
-
接根管,用嘴吹,6‘20-6’50
-jetman(飞人);
2018-12-30
(#11860664@0)
-
我用铁丝捅进20cm,很硬进不去了。用吸管对着吹,是通的。
-huanhuan2(Winter);
2018-12-30
(#11860718@0)
-
那就没问题。
-jetman(飞人);
2018-12-30
(#11860739@0)
-
见下面最新情况,只出现了一次,有人能解释下吗?
-huanhuan2(Winter);
2018-12-30
(#11860744@0)
-
我以前曾经坏过,结果是冷凝水导至,见连接。与你的不太一样,仅供参考。还有,你可Google你那个型号的西人论坛,可能会有启发。
-chli(不闲);
2018-12-30
(#11860200@0)
-
这是我如何修的。。。
-chli(不闲);
2018-12-30
(#11860204@0)
-
这个黑的冷凝水管我拆下过,朝里吹气是通的。排气扇倒是没想过会进水
-huanhuan2(Winter);
2018-12-30
(#11860564@0)
-
lennex这个型号冷凝水排水设计理念有问题。
-chli(不闲);
2018-12-31
(#11861040@0)
-
这么冷的天没暖气不行,需要不需要电暖器,你可以拿去用
-cocnut(cocnut);
2018-12-30
(#11860272@0)
+2
-
谢谢,买了个电暖器,多穿点衣服还对付,沒暖气的好处是早上睡的香,起不来
-huanhuan2(Winter);
2018-12-30
{18}
(#11860558@0)
-
哈!哈!
-cocnut(cocnut);
2018-12-30
(#11860788@0)
-
赞,真有韧劲儿。即使最终没能自己修好,也会从过程中学会不少东西
-piston(jim);
2018-12-30
(#11860454@0)
+3
-
他已经请了两次维修师傅,都没有结果。。。主板坏了,主板找不到。
-hunhunhunhun(不知道);
2018-12-30
(#11860528@0)
-
昨天来的师傳今天没回话,看来沒找到旧主板,明天Dealer上班买新主板,看能不能修好不然我是赔钱还挨冻,再换新炉子大出血[流泪][流泪][流泪]
-huanhuan2(Winter);
2018-12-30
{54}
(#11860552@0)
-
-chli(不闲); 哪个帖子,自己处理吧。估计不会有dealer有这东西。
-hunhunhunhun(不知道);
2018-12-30
(#11860563@0)
-
家里如果有壁炉,可以烧起来取暖
-piston(jim);
2018-12-30
(#11860634@0)
-
炉子就那几个主要部件,换了就好了。显然不用换新炉子。30年以上的非高效炉可以考虑换。
-chli(不闲);
2018-12-31
(#11861042@0)
-
先把ecobee拆下来直接装在炉子边上,这样就不用那个转换器了。如果还不行,最好再找个旧的普通themerstat,确认是不是炉子的问题。
-lifyy(lifyy);
2018-12-30
(#11860643@0)
-
ecobee已经完全拆下来,暂不用了。现在是R-W短线连接(师傅做的)。最新情况是,打开开关,持续1-2分钟,我看见点火的红光,持续大概十秒,就停止了。我试着重复这过程,不幸的是它不重复。记得有人说过,它有记忆功能。是不?
-huanhuan2(Winter);
2018-12-30
(#11860729@0)
-
对了,昨天还和师傅反复确认,他说不是EcoBee的问题,即使主板坏了,也不是EcoBee取电造成的。换了主板后,接上EcoBee还能用。
-huanhuan2(Winter);
2018-12-30
(#11860749@0)
-
还是我前面说过的,可能是气阀问题,用个螺丝刀把在阀上面敲一敲,我以前敲过两家都work过。。。
-ballfan(BALLFANS);
2018-12-30
(#11860769@0)
-
这么简单的一个问题,这里没有一个懂的,你问个什么?找个好的technician.
-111199991111(无情);
2018-12-30
(#11860786@0)
-
难找啊,这是第二个,看明天了
-huanhuan2(Winter);
2018-12-30
(#11860796@0)
-
你给我打电话吧我给你讲讲
-111199991111(无情);
2018-12-30
(#11860821@0)
-
“这么简单的一个问题,这里没有一个懂的,你问个什么?”----好吧,交给你了。而且LZ的出现的问题每次都不同。
-hunhunhunhun(不知道);
2018-12-31
(#11861088@0)
-
我用扳手敲打了几下,没用。两个气阀看着紧紧的,不用工具大力都拧不动。
-huanhuan2(Winter);
2018-12-30
{119}
(#11860793@0)
-
和这个阀(外面的)没有任何关系,球迷说的炉子里面的那个气阀。你可以把万用表接在电磁阀上,看看是电压(24VAC)消失,还是有电压没有气出来。
-hunhunhunhun(不知道);
2018-12-30
(#11860808@0)
-
这个电磁阀量电压我不会了,反正是没气出来
-huanhuan2(Winter);
2018-12-30
(#11860815@0)
-
那也会有声音出来,听一下。
-hunhunhunhun(不知道);
2018-12-30
(#11860816@0)
-
是的,是“○ 这个是煤气电磁开关,除了小黑软管,没有别的cable or wire. -huanhuan2(Winter); 12-28 {60} ”
这个煤气电磁开关。。。
-ballfan(BALLFANS);
2018-12-30
(#11860860@0)
-
要是年前能修好就是胜利✌️,不然还是换个新的吧,当局者迷。
-zhengsean(IT大叔);
2018-12-30
(#11860787@0)
+3
-
明天最后一天,希望这是师傅不要让我失望---绝望。。。
-huanhuan2(Winter);
2018-12-30
(#11860799@0)
-
虽然看不懂太深的技术问题,但是感觉到上面有些专家没把别人问题解决,人就闪的无影无综,比炉子灯闪的还快
-cocnut(cocnut);
2018-12-30
(#11860801@0)
-
而且这些所谓专家不按客户要求去做,我行我素当然不能解决问题
-cocnut(cocnut);
2018-12-30
(#11860811@0)
-
没有啥专家(估计出了ballfans),而且LZ自己动手能力差一些。
-hunhunhunhun(不知道);
2018-12-30
(#11860820@0)
-
??????????????????????//
-hnryll(松树);
2018-12-30
(#11860915@0)
-
你是男的还是女的?如果是男的,这样属于吝啬了。马上换新的锅炉吧,最近流感严重,家人感冒就损失更大了
-lotustears(oreo);
2018-12-30
(#11860869@0)
+1
-
看看气阀线圈是否断了(常见)。用强磁铁可以手动开启阀芯供气,帮助判断故障。我前不久修好一个Honeywell的控制阀
-piston(jim);
2018-12-31
{170}
(#11861096@0)
-
LZ啊!你今天能不能要你师傅快点解决问题,我已预感到换了板子又要出现Ecobee问题了,我的炉子也有问题了想等你结果好DIY,不过我炉子是老式的
-cocnut(cocnut);
2018-12-31
(#11861113@0)
-
你的炉子啥问题?估计没有我家的老。
-hunhunhunhun(不知道);
2018-12-31
(#11861115@0)
-
也是个怪问题,时不时来一下停机
-cocnut(cocnut);
2018-12-31
(#11861126@0)
-
停机有可能是Overheat。可以是真的overheat,比如过滤器引起的通风不好;也可能是limit switch工作不正常。
-hunhunhunhun(不知道);
2018-12-31
(#11861295@0)
-
看来你的炉子和我的炉子是一样故障,
-jetman(飞人);
2018-12-31
{378}
(#11861163@0)
-
可以用强磁铁手动开(吸)起阀芯,测试点火。里面应该是个柱塞阀,吸起时有明显的金属碰撞声音,和出气的声音
-piston(jim);
2018-12-31
(#11861182@0)
-
今天又叫第二个师傅忽悠了,叫我还能相信谁?!请推荐哪里可以买到主板York Furnace Control board 265904?
-huanhuan2(Winter);
2018-12-31
{658}
(#11861772@0)
-
哪里锅炉1000? 不是三千多吗
-qianshiyuanjia(purple fish);
2018-12-31
(#11861791@0)
+1
-
别听他忽悠,其实他师傅先电话里给我说过,要拿政府Rebate, 要花600做Audit, Audit人今天下午也不在,要等2号上班。
-huanhuan2(Winter);
2018-12-31
(#11861826@0)
-
你又要上套,人工你没有算?
-hunhunhunhun(不知道);
2018-12-31
(#11861939@0)
+1
-
反正这都是套路, 行话, 故障找不到就是主板坏了, 换主板, 换主板还修不好就换炉子.
-yuanfanback(归来的远帆);
2018-12-31
(#11861804@0)
-
现在没有以前不修好不收费的了,所以即使修不好,找个理由扯,检查费、车马费照收。第二个师傅要价还不低,以为靠谱点,结果一样。
-huanhuan2(Winter);
2018-12-31
(#11861835@0)
-
现在黑啊, 我们那时候最头痛的就是去修暖气炉, 有时候毛病显而易见,就是因为买不到配件收不到钱, 加拿大又不像美国, 在美国那些供应商的商店是认钱不认人, 只要给钱什么人买不重要, 加拿大那些专业店要认买货人的执照, 宁可不做生意也不卖给你.
-yuanfanback(归来的远帆);
2019-1-20
(#11889751@0)
-
是不是Dealer只卖给有License的人?我们自己买还不行?
-huanhuan2(Winter);
2018-12-31
(#11861838@0)
-
哥们儿,
-sanmudi(没有昵称);
2018-12-31
{210}
(#11861854@0)
-
谢谢了刚确认了,YORK有自己的经销,只卖有License的人。我准备再换个师傅,不信找不到靠谱的。
-huanhuan2(Winter);
2018-12-31
{83}
(#11861894@0)
-
外面好冷啊 家里10度有吗?早点换吧,对房子也不好
-lucky(azzy);
2018-12-31
(#11861897@0)
-
你那个炉子是2stage的, 有两个pressure switches, 电磁阀也是特殊的,电路也更复杂点,所以真正懂furnace 的人不敢轻易跟你的贴, 你在找技工的时候要提醒人家,谢谢你及时更新信息,
-water9(plumbingheatinggas);
2018-12-31
(#11861996@0)
-
这不是扯淡吗?简单的炉子,两波师傅连个问题都没有找到;这样的维修技能就敢出去维修,在这个行业自己作死。估计很多人连电流,CO等不会测试。
-hunhunhunhun(不知道);
2019-1-1
(#11862201@0)
-
楼主还没修好吗?现在确定是控制板的问题吗?
-bluesky2000(bluesky2000);
2019-1-1
(#11862333@0)
-
其实很简单,r,w短路以后,第一步,小风扇(inducer)启动,然后主板检测pressure switch,
-water9(plumbingheatinggas);
2019-1-1
{528}
(#11862367@0)
-
说的好,但楼主动手能力差一点儿,电压不会量,而且焦急,没静下来看YouTube 。其实应该YouTube 都能解决大部分问题,而且请的维修人员基本也是那个检测方法,而且最后被套路。如果判断真是主板,eBay 有。
-ontario_2014(rolian);
2019-1-1
(#11862435@0)
-
现在几个师傅确定主板问题 ,那就换呗,YORK的主板只买给有license的,所以还是要找所谓师傅买,再宰也认了,只求早修好
-huanhuan2(Winter);
2019-1-1
(#11862452@0)
-
FYI: Email from Master Group
-huanhuan2(Winter);
2019-1-4
{668}
(#11867009@0)
-
明天晚上零下15度,要抓紧了
-redroses(rose);
2018-12-31
(#11861898@0)
+3
-
ballfan(BALLFANS), 既然做生意,你就帮LZ修一下吧,看在网友的面上----人冻坏了可不好。
-hunhunhunhun(不知道);
2018-12-31
(#11861917@0)
+1
-
这太麻烦了,是我就 第一个师傅不行就马上登记 煤气公司的保修计划了
-bigcatf2(ToBe);
2019-1-1
(#11862051@0)
+1
-
哥们不知道,可惜我不是做生意的,和你一样,都是闲了帮朋友忙的。。。gas行业垄断,没有licence是不可以做生意收钱的,所以,楼主要买配件必须找有licence的,没有办法。。。
-ballfan(BALLFANS);
2019-1-1
{97}
(#11862064@0)
+1
-
我半年前装的NEST, 空调转暖气的时候也出过问题。我出个要挨砖的建议,在Kijiji 上找个懂Ecobee的西人师傅。
-babyface(★☆给点儿阳光就灿烂);
2019-1-1
(#11862384@0)
+2
-
就像楼上说的,其实很简单,按照步骤就能搞定。
-bluesky2000(bluesky2000);
2019-1-1
(#11862392@0)
-
必须承认 这维修方面,老外比华人师傅诚实,华人师傅心理没有真正认可维修工角色
-zhayan(杭州藕粉);
2019-1-1
(#11862393@0)
+1
-
做这一行的维修不太容易,因为要有保险,别的行业很多都可以做兼职(都属于建筑行业trades people),所以都不愿意花时间做trouble shooting, 楼主静下心来多看几个youtube搞清楚furnace的工作原理应该能找到问题原因,
-water9(plumbingheatinggas);
2019-1-1
(#11862406@0)
-
现在找到的问题就是主板问题,换了主板,才能发现是否还有其它问题。换火炉是解决所有问题,时间也要长。
-huanhuan2(Winter);
2019-1-1
(#11862596@0)
-
换火炉,空调如何办?也只能一起换掉。
-hunhunhunhun(不知道);
2019-1-1
(#11862664@0)
+1
-
暖炉跟空调没有大的关系,只是空调温度控制器的连线到暖炉主板,蒸发器在铁皮管道里,
-water9(plumbingheatinggas);
2019-1-1
(#11862757@0)
+1
-
对于我们来说,买了house, 才需要学这些,但是对于本地白人来说,已经每家每户用这些暖气,水炉子半个多世纪了。经验还是多些。
-babyface(★☆给点儿阳光就灿烂);
2019-1-1
(#11862505@0)
-
Ecobee 就是送一个启动命令,跟短路联线一样,干嘛还要懂ecobee,而且他跟技术支持持联系了。这个应该不是ecobee 的问题。
-ontario_2014(rolian);
2019-1-1
(#11862440@0)
+1
-
所以,他自己也说要挨砖了。。。
-ballfan(BALLFANS);
2019-1-1
(#11862522@0)
-
帮楼主测量了一下,
-hbwang(nick);
2019-1-1
{702}
(#11862697@0)
+3
-
把控制板拆下来吧现象像排风电机和电磁阀 relays同时虚焊。
-jetman(飞人);
2019-1-1
{39}
(#11862732@0)
-
拆了
-hbwang(nick);
2019-1-1
(#11862830@0)
-
赞,真正的热心人
-piston(jim);
2019-1-1
(#11862755@0)
-
电磁线圈可以量一下,看看是否开路。好的线圈量时电阻初始有几欧姆然后感应升到100多欧姆
-piston(jim);
2019-1-1
(#11862758@0)
-
哪一个电磁线圈?变压器还是电磁阀?
-hbwang(nick);
2019-1-1
(#11862831@0)
-
电磁阀的线圈,像这个,前不久我碰到这个线圈坏了,开路
-piston(jim);
2019-1-1
{57}
(#11862856@0)
-
我是测电磁阀线5v电压就不关注了,本来想加电24v 看是否通气的
-hbwang(nick);
2019-1-1
(#11862864@0)
-
我当时测的线圈电压是交流56伏,有点儿怪,但两块表都读出这个值
-piston(jim);
2019-1-1
(#11862893@0)
-
有没有先把Pressure switches摘出来测,应该是开路的,如果是通的那么只要加电就出错,只有在inducer 工作时把它吸合才对,
-water9(plumbingheatinggas);
2019-1-1
(#11862771@0)
-
测过,不加电是开。
-hbwang(nick);
2019-1-1
(#11862780@0)
-
拿基本就是主板问题了,不过可以在重复上述过程当中把电磁阀摘出来,单独测给电磁阀电线上的电压,看是否还是5伏特,因为如果电磁阀线圈有问题,在线测试的话可能会把电压拉下来,如果问题依旧建议换single stage furnace,
-water9(plumbingheatinggas);
2019-1-1
(#11862788@0)
-
单独测电磁阀线一过性5v
-hbwang(nick);
2019-1-1
(#11862833@0)
-
说明书给电磁阀的电压是24v
-hbwang(nick);
2019-1-1
(#11862835@0)
-
就是这个气阀继电器没有输出,气阀打不开了,可能是板子上面驱动电源部分烧了。。。
-ballfan(BALLFANS);
2019-1-2
(#11864178@0)
-
电磁阀和燃烧stage还有个风压管,这个电磁阀有两个控制Hi和M 还有个小压力开关
-hbwang(nick);
2019-1-1
(#11862861@0)
-
RW 短路时FaultCode是多少?
-bluesky2000(bluesky2000);
2019-1-1
(#11862793@0)
-
谁来做Service,也必须看FaultCode,通过Code就告诉你那块坏了,去哪查。炉子是不复杂,没准换个Filter就全解决了。
-bluesky2000(bluesky2000);
2019-1-1
(#11862807@0)
-
如果换filter解决问题,那说明是过热了,所有的code做依据都是基于主板是好的为基础,他现在点不着炉,还没到过热那步,因为主板最贵,所以先bypass外围的传感器,再来量主板给的电压,如果不合逻辑的话就是主板的问题,
-water9(plumbingheatinggas);
2019-1-1
(#11862814@0)
+1
-
感觉对应
1slow green
2amber long on ,short off
3steady on red
-hbwang(nick);
2019-1-1
(#11862838@0)
-
似乎对应
-hbwang(nick);
2019-1-1
{165}
(#11862829@0)
-
如果灯停留在SteadyOnRed, 说明控制板坏了。
-bluesky2000(bluesky2000);
2019-1-1
(#11862839@0)
-
红灯也不是长亮 因为很快就重新启动了
-hbwang(nick);
2019-1-1
(#11862844@0)
-
最后Code灯是什么呢?不能总启动循环,总有停下来的时候。
-bluesky2000(bluesky2000);
2019-1-1
(#11862847@0)
-
红或灭
-hbwang(nick);
2019-1-1
(#11862860@0)
-
简单点吧,短路RW,五分钟后回来,是什么灯?
-bluesky2000(bluesky2000);
2019-1-1
(#11862865@0)
-
重复启动或者一点动静没有
-hbwang(nick);
2019-1-1
(#11862869@0)
-
电路图
-hbwang(nick);
2019-1-1
{57}
(#11862872@0)
-
人工临时方案,危险仅供学习,切勿实践。主板rg短路,循环风机开启。取主板24v,接电磁阀和排风电机(风机效率70%),点火器。着火后断开点火器,人在炉子旁边看着不要灭火,燃气,co报警器多放几个在旁边
-hbwang(nick);
2019-1-1
(#11862890@0)
-
还有,变压器输出的电压需要整流变压到5伏特左右,如果有问题主板肯定控制有问题,不过测量,修理起来更麻烦,这就是为什么搞专业维修的总建议换新的了,
-water9(plumbingheatinggas);
2019-1-1
(#11862808@0)
-
不是很好测 线相互掣肘 没有空间
-hbwang(nick);
2019-1-1
(#11862832@0)
-
把循环风机拆下来才有可能测
-hbwang(nick);
2019-1-1
(#11862843@0)
-
还没修好? 耐心和耐力真好
-dashixiong(nonono);
2019-1-1
(#11862760@0)
+2
-
还没修好啊, 同情一把, 可惜鞭长莫及, 只能在此鼓励一下.
-yuanfanback(归来的远帆);
2019-1-1
(#11862781@0)
-
建议你将gas valve短时间用线联在24v,call for heat,如burner能够点火,那主板肯定就坏了。如买原厂的主板有困难,试试在ebay上买Honeywell s9200u1000/u,买前查查是否你炉子的型号也适用在那个通用主板范围内。估计eBay 上可能不用gas license.
-jimli6(jimli6);
2019-1-1
(#11862895@0)
-
美国不到100就可以买,但邮寄需要时间。还有一个情况第二个师傅想先打火,但没有成功,具体原因不明
-hbwang(nick);
2019-1-1
(#11862905@0)
-
其实Gas valve 5v,如果准确的话,那个主板就坏了。
-jimli6(jimli6);
2019-1-1
(#11862908@0)
-
电磁阀各种电压都有 只能看说明书
-hbwang(nick);
2019-1-1
(#11862915@0)
-
炉子的FaultCode就像车的读码一样,定位车为什么打不着火。这个是基本的程序,如果没有读码,就按照炉子的HeatingSequence一步一步排查。先排烟,再点火,然后是风机。
-bluesky2000(bluesky2000);
2019-1-1
{123}
(#11862916@0)
+1
-
理论上是,但我看电路图和code,发现有三个感应器是串联的,还分别有自己code。单片机怎么判读出来到底是哪一个感应器出了问题?
-hbwang(nick);
2019-1-1
(#11862927@0)
-
一般说是判断不出来。只能给个i查问题的方向。
-bluesky2000(bluesky2000);
2019-1-1
(#11862953@0)
-
办法有。何况还有智能输出的传感器。
-hnryll(松树);
2019-1-2
(#11863289@0)
-
传感器开关上并联电阻。假设三传感器开关分别有100/1k/10k电阻并联,正常开关闭合。电阻们被短路。
-jetman(飞人);
2019-1-2
{70}
(#11863351@0)
-
没有并联。
-hbwang(nick);
2019-1-2
(#11863665@0)
-
不同时段十逻辑分析
-cocnut(cocnut);
2019-1-2
(#11863753@0)
-
专业
-piston(jim);
2019-1-1
(#11862939@0)
+1
-
有个类似的板子可以邮寄到加拿大
-hbwang(nick);
2019-1-1
(#11862921@0)
+1
-
首先怀疑, 排除的是 flame sensor
-iamnew(Iamnew);
2019-1-2
(#11863226@0)
-
终于有暖气了。衷心感谢以上所有网友热心救助,特别鸣谢Nick亲自上门检测。大赞朱师傅,专业守信。还有一个小问题求教。先把故事讲完。昨天联系了朱师傅,朱师傅本来有约,听了我的情况,决定先解决我的问题。今天一大早就去买了主板,八点上门,初步检查后,剪断两根线,跳过主板,暖气可以起来,排除了电机或其它问题。决定换上新板,接上EcoBee后,暖气开始供应,结束的冰凉的时代。小问题是所有连线都正常,但EcoBee找不到空调,也没地方设置。主板上的跳线也是对的。问题出在哪儿?
-huanhuan2(Winter);
2019-1-2
{340}
(#11863404@0)
+1
-
换主板多少钱? 求朱师傅电话
-dahuyu(dahuyu);
2019-1-2
(#11863427@0)
+1
-
PM
-huanhuan2(Winter);
2019-1-2
(#11863477@0)
-
照张控制板的接线图,你的Ecobee是几代的型号?
-bluesky2000(bluesky2000);
2019-1-2
(#11863432@0)
-
Thermostat Model
ecobee3 lite
Firmware Version
4.2.0.392
-huanhuan2(Winter);
2019-1-2
{122}
(#11863465@0)
-
正常这里有四项,Heat, Cool, Auto, Off
-huanhuan2(Winter);
2019-1-2
{60}
(#11863485@0)
-
温控器到小白盒子的线要接对,因为这部分走的是信号 不是单纯短路,否则会出现这样的情况
-hbwang(nick);
2019-1-2
(#11863507@0)
-
这是新控制板的线路图
-huanhuan2(Winter);
2019-1-2
{238}
(#11863504@0)
-
始终对空调接到Y1有疑问,如果是两级压缩机的空调,需要接到Y1和Y2,如果只是一级压缩机,接到Y上。换完Ecobee后使用过空调吗?是否正常?
-bluesky2000(bluesky2000);
2019-1-2
(#11863516@0)
+1
-
去年四月换的EcoBee, 夏天用过空调没问题
-huanhuan2(Winter);
2019-1-2
(#11863528@0)
-
这是新板的接线照片,是不是空调线有问题?
-huanhuan2(Winter);
2019-1-2
{238}
(#11863833@0)
-
比较图,原来的黑线接Y1,现在接到 Y2了?
-huanhuan2(Winter);
2019-1-2
{60}
(#11863838@0)
-
重新接线后,还是不见空调?
-huanhuan2(Winter);
2019-1-2
{60}
(#11863873@0)
-
Y线控制空调压缩机的,和暖气没有关系----如果不对,也要等到夏天试过。原来你这里有个转接盒子啊?电压、电流一致吗?小心为上。
-hunhunhunhun(不知道);
2019-1-2
(#11863882@0)
-
转接盒子是EcoBee带的,四线转五线
-huanhuan2(Winter);
2019-1-2
(#11863888@0)
-
是和暖气没有关系,但原来EcoBee可以认空调,即四个选项:Heat, Cool, Auto, Off. 现在只有两个:Heat和Off. 点解?
-huanhuan2(Winter);
2019-1-2
(#11863890@0)
-
这样啊,让大家想一下。
-hunhunhunhun(不知道);
2019-1-2
(#11863895@0)
-
这个图,绿线上面接C,下面接的G,对吗?
-huanhuan2(Winter);
2019-1-2
{60}
(#11863924@0)
-
你的接线图太多,不知道哪个是最后接的。从转换盒到炉子应该是接到Y/Y2上是对的。找出你的Ecobee的小绿本安装手册,有接线图。接线应该没问题。
-bluesky2000(bluesky2000);
2019-1-2
(#11863939@0)
-
看起来很简单,没接错了,为什么空调出不来?
-huanhuan2(Winter);
2019-1-2
{119}
(#11863964@0)
-
Wiring Diagram
-bluesky2000(bluesky2000);
2019-1-2
{62}
(#11863942@0)
-
Reset Ecobee.
-bluesky2000(bluesky2000);
2019-1-2
(#11863953@0)
-
How? 断电重启也一样
-huanhuan2(Winter);
2019-1-2
(#11863960@0)
-
应该是在Ecobee的Menu里选Reset。
-bluesky2000(bluesky2000);
2019-1-2
(#11863962@0)
-
谢谢,reset后OK了。
-huanhuan2(Winter);
2019-1-2
(#11863988@0)
-
ECOBEE 空调Y线一根都没有连接,估计这个原因你找不到空调的选项。Peak那里我不懂。。。
-hunhunhunhun(不知道);
2019-1-2
(#11864314@0)
+1
-
求朱师傅电话
-tracyl(花花);
2019-1-2
(#11863475@0)
-
PMed
-huanhuan2(Winter);
2019-1-2
(#11863484@0)
-
求朱师傅电话
-tzm_oasis(绿洲);
2019-1-2
(#11863490@0)
-
PMed
-huanhuan2(Winter);
2019-1-2
(#11863494@0)
-
朱师傅要火了。
-fishinsea(长翅膀的鱼);
2019-1-2
(#11863519@0)
-
好人就该火
-huanhuan2(Winter);
2019-1-2
(#11863531@0)
-
同意。能PM朱师傅的联系方式吗,留作备用,虽然我2年前才换的炉子。
-fishinsea(长翅膀的鱼);
2019-1-2
(#11863617@0)
-
这事一开始就说是主板的问题,看来第一个师傅也是对的
-jzsjw(jzsjw);
2019-1-2
(#11863600@0)
-
对的 但价格太高。最后一个师傅市场价格。当然最实惠的方案就是网上买个几十元的主板自己换。人工临时方案晚上开火几个小时等邮寄时间。
-hbwang(nick);
2019-1-2
(#11863607@0)
-
楼主不用维护计划(reliance 维护计划才15块一个月),又运气不好,在错误的时间坏了重要的东西。普通用户就应该用维护计划,如果计划都修不好就换新炉
-bigcatf2(ToBe);
2019-1-2
(#11863611@0)
+1
-
九月才过的保修期,谁能想到它准时坏?!
-huanhuan2(Winter);
2019-1-2
(#11863615@0)
-
不好意思啊,有个疑问,朱师傅不能回答你这个小问题?
-cjkm616(天马行空);
2019-1-2
(#11863610@0)
-
朱师傳上午有另一个客户,他一大早去买板(七点开门),八点就来了,按照说明书装的,看起来都沒错,没有时间推敲,又不是很急的事,就赶去客户家。我插了个队,本也不好意思,这里高人又多,看能不能自己解决
-huanhuan2(Winter);
2019-1-2
{56}
(#11863624@0)
-
真心劝你放弃那个免费的bee, 接不好了下次还烧你主板
-guanshui88(约定);
2019-1-2
(#11863783@0)
-
朱师傳也说跟EcoBee没关系,主板十年了,难免有个感冒发烧
-huanhuan2(Winter);
2019-1-2
(#11863807@0)
-
恭喜问题得到解决!
-rebecasmith(rebecasmith);
2019-1-2
(#11863865@0)
-
谢谢
-huanhuan2(Winter);
2019-1-2
(#11863896@0)
-
求PM朱师傅电话
-alanhe(alanhe);
2019-1-4
(#11866415@0)
-
恭喜恭喜,不管怎么说最后问题解决,你估计也成暖炉的半个专家了。
-zhengsean(IT大叔);
2019-1-2
(#11863752@0)
-
谢谢,专家谈不上,至少知道谁是蒙事的
-huanhuan2(Winter);
2019-1-2
(#11863811@0)
+1
-
蒙事?这话说的很不地道。第一个师傅就告诉你主板坏你因为价钱没让做,自己在折腾。炉子本来就是一个简单东西,经常出问题的就是上边说那些,查来查去不着边际就是因为那些都没有坏。大家都是热心帮助,怎么就蒙事了。
-bangmang(大小写均可);
2019-1-2
(#11864188@0)
-
我食言一次,本不想理你,又点我气头上了。第一个师傅说主板要上千,第二个师傅故意不买板,你不明白为什么吗?!我没说大家蒙事,别故意挑事,大家看得清楚。早上起来看到大家半夜还在发帖,真心感动,也让我没有放弃。你不帮忙就算了,别在这里捣浆糊。
-huanhuan2(Winter);
2019-1-2
(#11864228@0)
+3
-
没错,肯定学了不少东西
-piston(jim);
2019-1-2
(#11863849@0)
-
为什么一直都找华人师傅?家人冻了好几天,最后给某师付打个广告
-sweet_home(sweet_home);
2019-1-2
(#11863875@0)
+3
-
不是相信国人吗。扬善好过恶。
-huanhuan2(Winter);
2019-1-2
(#11863894@0)
-
楼主和楼主家人真有耐性,没暖气那么多天还能左折腾右上网。我家以前的类似情况,24小时内一定找到人上门来修,修不好三天内就换炉子。
-vicky2005(孩子她爹);
2019-1-2
(#11863933@0)
+2
-
终于修好了
-zhizihua(雨妮);
2019-1-2
(#11863947@0)
-
你再别提这茬了,现在我还气不顺呢, 第一天就叫了师傅,赶上周末和元旦,前面两个师傅,收了钱不见人,把时间耽误了。我一边加班一边现学,容易吗?!你们家运气好,行了吧。至此,再不回答这种贴。
-huanhuan2(Winter);
2019-1-2
(#11863970@0)
+4
-
修好了就好,好好总结吧,你已是专家了哈
-sanmudi(没有昵称);
2019-1-2
(#11864444@0)
-
前几天没有找到合适的师傅,再说人家也不是能马上给你维修的。
-hunhunhunhun(不知道);
2019-1-2
(#11863985@0)
-
我有个问题:你的炉子可能是Two stages,就是温度/速度一高,一低。但是你用的这个温度控制器,看照片上的连接感觉是只能控制第一种,one stage的。原来那个温度控制器那里去了?换回来吧,要不浪费了。
-hunhunhunhun(不知道);
2019-1-2
(#11863984@0)
-
对呀,我也注意到,EcoBee上只显示Stage1. 原来的温控器叫GreenOn收走了。EcoBee应该比原来的新,为什么不能控制Two Stages呢?
-huanhuan2(Winter);
2019-1-2
(#11863990@0)
-
你现在的设备配置是Ecobee , Furnace 都是TwoStage, 空调是OneStage。从Ecobee到炉子的控制线只有四根,增加到六根就能实现TwoStage控制,也不用那个转换盒了。
-bluesky2000(bluesky2000);
2019-1-2
(#11863995@0)
-
应该是这个图了,W2线从何而来?
-huanhuan2(Winter);
2019-1-2
{60}
(#11863998@0)
-
从FurnaceW2 到 Ecobee 的W2.这种接法是不用转换盒的。
-bluesky2000(bluesky2000);
2019-1-2
(#11864004@0)
-
那要在墙里穿根线,工程有点大有沒有无线解决方案
-huanhuan2(Winter);
2019-1-2
{18}
(#11864044@0)
-
如果这根线你可以拉的动,直接带一条尾巴出来。地下室没有装修,或者就在附近更容易。其实你这个问题就是ecobee那些人造成的,可以打电话投诉。
-hunhunhunhun(不知道);
2019-1-2
(#11864190@0)
-
无线解决方案通常操控温控器都是手机app, schedule设好后,一般很少改。如果把整个温控器拆下来,拿到火炉边,接六根线就很容易,反正温控器上网后,放在哪里都一样。可行吗?
-huanhuan2(Winter);
2019-1-2
{151}
(#11864428@0)
-
应该没有问题,只要信号可以达到Bee。。。
-ballfan(BALLFANS);
2019-1-2
(#11864437@0)
-
有第二个温度传感器的温控器可以这样,否则温控器放地下室会浪费很多燃气,因为温控器上的温度传感器只根据地下室的温度停机或开机。
-hbwang(nick);
2019-1-3
(#11864567@0)
-
你的温控器和炉子 也就十尺,很容易换
-hbwang(nick);
2019-1-3
(#11864568@0)
-
+100 好主意。
-hunhunhunhun(不知道);
2019-1-2
(#11864225@0)
-
问一下,是哪张照片显示的one stage的?
-reed(芦苇);
2019-1-2
(#11864154@0)
-
这张:
-hunhunhunhun(不知道);
2019-1-2
(#11864193@0)
-
oh 谢谢,W2没有接? 我还以为 Ecobee 面板有显示1 or 2 stage呢。
-reed(芦苇);
2019-1-2
(#11864312@0)
-
我估计完全一对一接好,应该可以看到这个选项----现在有点糊弄机器。
-hunhunhunhun(不知道);
2019-1-2
(#11864320@0)
-
Ecobee 面板有显示Heating status at stage 1, 我还纳闷什么时候显示 Stage 2
-huanhuan2(Winter);
2019-1-2
(#11864371@0)
-
那个stage2是个鸡肋,没有必要。。。
-ballfan(BALLFANS);
2019-1-2
(#11864385@0)
-
在控制板上,有个Two Stage 的跳线,不要设定到Off,机器会自动调转到TwoStage。
-bluesky2000(bluesky2000);
2019-1-2
(#11864448@0)
-
是Heat Delay Jumper还是Hi Heat Delay Jumper?
-huanhuan2(Winter);
2019-1-3
{60}
(#11865051@0)
-
my finding
-reed(芦苇);
2019-1-3
(#11865455@0)
-
EcoBee Support repliedYou will have to run a wire from W2 at the thermostat to the furnace control board in case you want thermostat to control stage 2 heating.
-huanhuan2(Winter);
2019-1-3
{138}
(#11865788@0)
-
+1
-piston(jim);
2019-1-3
(#11865797@0)
-
Hi Heat Delay Jumper 设定到10, 炉子自动跳转到TwoStage。
-bluesky2000(bluesky2000);
2019-1-3
(#11865905@0)
-
Hi Heat Delay Jumper 设定到了10(原来是OFF), 火炉起来十多分钟,跟原来一样,没感觉到Stage2.
-huanhuan2(Winter);
2019-1-4
(#11867195@0)
-
我自己的理解:stage1, stage2是“温度控制器”控制的,根据温差---设定的温度和现在的温度。
-hunhunhunhun(不知道);
2019-1-4
(#11867217@0)
-
我猜温控器如果有W2连线,可以直接设置stage1或stage2启动或返回Heating running stage. 主板设置跳线(10分钟Delay), 表示如果十分钟没达到设定温度,应该启动Stage2.
-huanhuan2(Winter);
2019-1-4
(#11867239@0)
-
你的炉子不知道,Goodman的炉子可以用 1 stage thermostat控制 2stage炉子,在某段时间内达不到设定问题,炉子自动换到高热输出状态。看下面链接23页左下角
-biosfix(BIOSFIX);
2019-1-4
(#11867227@0)
-
Figure 31: #3 set OFF and #4 set ON(自动转换)OFF(5分钟delay). 就是用 1 stage thermostat控制 2 stages炉子. 但没提W2线存不存在。
-huanhuan2(Winter);
2019-1-4
(#11867257@0)
-
只需要炉子上有W2,温控器没有,炉子也能进入high heat output 模式
-biosfix(BIOSFIX);
2019-1-4
(#11867294@0)
-
@sailor: 能给查查,这个帖子是不是美丽家居板块 回复最多的帖子?如果还不是,兄弟们还可以加把劲!
-reed(芦苇);
2019-1-4
(#11867263@0)
-
老大有没有奖励?
-huanhuan2(Winter);
2019-1-4
(#11867267@0)
-
麻烦PM朱师傅电话,thanks
-susan678(西柚);
2019-1-12
(#11878430@0)
-
还没修好? 惨了,!
-yuanfanback(归来的远帆);
2019-1-13
(#11878710@0)
-
修是修好了,有一天又出状况了,下班回家,温度没起来,呼呼出冷风,赶紧关机,再重启,风机启动转,沒打火,等了十来分钟,仍然没打火,就断电,把上次设的staging delay 10 minutes set back to off.上电,开机,打火,暖风吹
-huanhuan2(Winter);
2019-1-13
{147}
(#11879035@0)
-
麻烦PM朱师傅电话,thanks -
-jiangsu1996(宣武门大胡籚);
2019-1-20
(#11889525@0)
-
PMed
-huanhuan2(Winter);
2019-1-13
(#11879054@0)
-
求朱师傅电话
-vvgege(Vvgege);
2019-1-21
(#11891973@0)
-
新问题,上回书暖气炉修好后,湿度显示45%,在正常范围,过几天感觉有点干,注意到温度降到39%,检查加湿器滴水正常,动了动开关,发现又降到35%,而且明显干燥,就在加湿器里放了一块大海绵(吸水),在加湿器工作时,人工往海绵注水,几次以后,明显觉得湿度增加了,但EcoBee湿度显示33%,还在下降,是怎么回事?
-huanhuan2(Winter);
2019-1-13
{197}
(#11879052@0)
-
冬天了,正常。加湿器开到最大也会干燥的。
-hunhunhunhun(不知道);
2019-1-14
(#11880491@0)
-
还有,如果你的加湿器是电路板直接驱动的、马达滚筒的那种,容易坏电路板。
-hunhunhunhun(不知道);
2019-1-14
(#11881061@0)
-
你怎么没完了
-yuanfanback(归来的远帆);
2019-1-20
(#11890278@0)
-
完了朱师傅就没生意了?
-jiage(北伐先锋);
2019-1-20
(#11890352@0)
-
修理人员最后一招就是换电路板,凡走到这一招棋的修理人员都不及格,可有人不服气,说:"我还能换电路板,有人直接就换炉子"
-yuanfanback(归来的远帆);
2019-1-21
(#11891035@0)