This topic has been archived. It cannot be replied.
-
枫下家园 / 美丽家居 / 小电chainsaw链子脱下来,怎么装回去呢?油管上看怎么很复杂的样子。
-linsh(坐看云起);
2020-4-27
(#12905641@0)
-
非常简单,调调螺丝即可
-landn(九天九地之行者);
2020-4-27
(#12905651@0)
-
有个纽,怎么也旋不动。
-linsh(坐看云起);
2020-4-27
(#12905679@0)
-
掉链子常见问题吗?第一次用。
-linsh(坐看云起);
2020-4-27
(#12905684@0)
-
常见问题。你的是什么锯?BD的电动18inch?
-spitfireto(很有意思);
2020-4-27
(#12905829@0)
-
电动的,York work.拧开了那个纽,老装不紧,用用又掉。不知什么原因。🙄
-linsh(坐看云起);
2020-4-27
(#12906085@0)
-
tension太松了吧?照一张调整松紧的机构的照片看看
-spitfireto(很有意思);
2020-4-27
(#12906123@0)
-
看来油管,是chain too loose, but need to find out where is tension adjustment. Will check tomorrow. Thanks again!
-linsh(坐看云起);
2020-4-27
(#12906351@0)
-
应该是很便宜的,可以当电动pole saw.
-linsh(坐看云起);
2020-4-27
{56}
(#12906090@0)
-
翻过来拍张照片
-spitfireto(很有意思);
2020-4-27
(#12906117@0)
-
锁扣纽的一边。谢谢!
-linsh(坐看云起);
2020-4-27
{56}
(#12906340@0)
-
所以这个黄色的旋钮往逆时针方向旋转,就可以把上面这个塑料盖拿下来,对吧?再照一张取下塑料盖的照片。
-spitfireto(很有意思);
2020-4-27
(#12906377@0)
+1
-
谢谢!网上找到他家的一个产品有2个旋钮。今天没注意到,明天再仔细找找。
-linsh(坐看云起);
2020-4-27
{56}
(#12906382@0)
-
我今天就是把塑料盖打开,把链子装入chian house。没上紧就觉得链子太松所以老掉。😁
-linsh(坐看云起);
2020-4-27
(#12906386@0)
-
这款没有2旋钮。或许象你说的在盖子里面。
-linsh(坐看云起);
2020-4-27
{56}
(#12906403@0)
-
打开盖子,里面好像没调节钮。
-linsh(坐看云起);
2020-4-28
{56}
(#12908092@0)
-
照片看得不是很清楚。但是我画红圈的部分是什么?
-spitfireto(很有意思);
2020-4-28
{246}
(#12908126@0)
-
你画圈的上面有图标看不懂,不敢打开。觉得是深部修理的。
-linsh(坐看云起);
2020-4-28
(#12908177@0)
-
锯子板边上有个小螺丝,我刚刚把它旋紧了,链子还是有点垂着,但手动拉得起来。算装好了?
-linsh(坐看云起);
2020-4-28
(#12908189@0)
-
好像是先把黄旋钮拧松,然后装上链条,然后用螺丝刀顺时针转动板子下面的螺丝,小扭就把板子向外拉紧了,等螺丝刀转不动了就把黄旋钮拧紧固定住。
-canyy(canyy);
2020-4-28
(#12908414@0)
-
是的
-spitfireto(很有意思);
2020-4-28
(#12908553@0)
-
我是这么操作的,现在不掉链子了尽管有些松。我想紧点也行锯得更有力。谢谢!
-linsh(坐看云起);
2020-4-28
(#12908988@0)
-
喷点WD40到拉紧螺丝上,螺丝被油腻腻住了。另外每次用之前要加润滑油链条才跑的欢。
-canyy(canyy);
2020-4-28
(#12909076@0)
-
请问润滑油抹链子?和装在罐子里的油不一样吧?英文?WD喷螺丝是调整松紧度的那个螺丝还是螺丝连着的强力弹簧?谢谢!
-linsh(坐看云起);
2020-4-28
(#12909275@0)
-
应该有个口可以灌专用润滑机油的,不是黄油。我是在Canadian tire买的一罐。你不是说链条还有点松,那就喷调松紧的螺丝然后再拧一下,看是否能再拉紧一些。
-canyy(canyy);
2020-4-29
(#12909428@0)
-
装罐子里的油一直有的。我试试用WD 40清理下调节机关,应该是粉尘+油聚集上面导致调节幅度受限。谢谢!
-linsh(坐看云起);
2020-4-29
(#12909565@0)
-
找到小机关,旋到最紧,看着还是偏松。
-linsh(坐看云起);
2020-4-28
{56}
(#12908175@0)
-
你是不是不敢拧紧了啊?还是有点松。照一张没有盖盖子的时候,那个键的位置。看看bar的长孔现在什么样子。如果你真的把螺丝拧到死都还不够紧,说明键滑块在螺杆的位置太靠前了。你把bar拆下来,然后单独调滑块位置。让滑块在螺杆的位置靠后一些。
-spitfireto(很有意思);
2020-4-28
(#12908256@0)
-
旋得很紧了,现在凑合能跑不掉链子…估计得调整里面那个图示的位置,不敢动。谢谢耐心指导!
-linsh(坐看云起);
2020-4-28
(#12908349@0)
-
看看是不是还是哪里有问题或者找说明书看看调整的细节。调合适后应该是不会露出任何空间,用手拉,能拉开1/8 到1/4 inch.
-maplevince(二分之一);
2020-4-28
(#12909067@0)
-
谢谢!说明书没找到。总结下你们几个的建议好像更明白trouble shooting process了。很好的学习机会。😀
-linsh(坐看云起);
2020-4-29
(#12909603@0)
-
1个旋钮的锯全都存在同样的问题,因为只有1个点固定,所以前端的稍微偏转,锯片就掉下来了。这个缺点无解。 有两个固定点的就完全没有类似问题,几个小时下来就没有掉过。
-richard100(冬青);
2020-5-4
(#12924072@0)
-
谢谢修好了。链子上不紧,因为调整弹簧粘住了,还有chain house里面有沙土。清理干净后就完全正常了。☺️
-linsh(坐看云起);
2020-5-4
(#12924950@0)
-
不用打开盖子吗?调哪里的螺丝?
-linsh(坐看云起);
2020-4-27
(#12905689@0)