This topic has been archived. It cannot be replied.
-
枫下家园 / 美丽家居 / Electrical wire fishing的问题:如何不破墙,从现有的插座横向延长?我可以穿洞过几根木头没有问题。可是那个铁盒子里空间那么小,怎么往外出线?
-2841999(四友);
2019-12-29
(#12565265@0)
-
先把铁盒松开拿出来
-joe_hxw(go);
2019-12-29
(#12565273@0)
-
这办法可行。铁盒外面的钉子/螺丝怎么卸下来呢?
-2841999(四友);
2019-12-29
(#12565309@0)
-
铁盒子是撬的下来的。如果撬坏了,就留在墙里,都不用拿出来。让它掉下去,然后按个新的。我做过很多次。你可能要去买一套撬东西的工具,大概十几块。
-kansaslpa(lpa);
2019-12-31
(#12567605@0)
-
不破坏drywall是拿不出来的。铁盒边上有几根蟹爪,扒住木框。
-2841999(四友);
2019-12-31
(#12567689@0)
-
你只要把钉子弄松了,哪几个爪子没多少力气的。另外,drywall稍微损坏不碍事的,因为面板要大的多,够挡住就行。
-kansaslpa(lpa);
2019-12-31
(#12567778@0)
-
另外,接线盒四面都有孔。你要去买一个拖线的钢丝。这东西像卷尺一样。
-kansaslpa(lpa);
2019-12-31
(#12567624@0)
-
普通1个位的接线盒只有上下有孔,左右没有,
-googlebot(bot);
2019-12-31
(#12567637@0)
-
没有。左右有斜孔,拧螺丝用的。米国的塑料盒子会不会好一点?
-2841999(四友);
2019-12-31
(#12567674@0)
-
如果是塑料的,哪你直接用电钻打孔就好了。嫌空间不够,就打大点孔。
-kansaslpa(lpa);
2019-12-31
(#12567686@0)
-
我能想到的另外一个办法是在同样两根木框的反面墙上先加一个插座。
-2841999(四友);
2019-12-29
(#12565336@0)
-
不可能把铁盒松开,钉子在里面钉的,我看youtube是在铁盒上面开个窄槽穿线,
-googlebot(bot);
2019-12-29
(#12565511@0)
-
可以松开。干活的时候,要有理想。
-kansaslpa(lpa);
2019-12-31
(#12567665@0)
-
...
-troyd(.);
2019-12-29
{126}
(#12565302@0)
-
盒子有4个出线口,每个都有铁盖子盖住,你把盖子掰开,不就能出线了吗?
-canadagoose(秋雁🇨🇦);
2019-12-30
(#12565626@0)
-
都没干过说的简单,孔是上下的,他是横向穿线,外面都看不到电线,
-googlebot(bot);
2019-12-30
(#12565627@0)
-
这就看你的技术了,用fishing wire 从新插座fish 到旧插座顶部,然后勾下来
-canadagoose(秋雁🇨🇦);
2019-12-30
(#12565652@0)
+2
-
肯定要破墙,
-googlebot(bot);
2019-12-30
(#12565629@0)
-
看看小C的录像链接就知道了,不过那个是走的明线。
-thegirlbefore(Jane);
2019-12-30
(#12565659@0)
-
要是暗线容易走,我能不说嘛。这相当于 Directional Drill。找那种可以弯曲蛇一样的 drill bit 试试吧。
-troyd(.);
2019-12-30
(#12565672@0)
-
我也在和LD争论加一个灯是走暗线还是明线。
-thegirlbefore(Jane);
2019-12-30
(#12565716@0)
-
这个决定得看人多矫情。如果容易能找到起点和目的点中间点作为个可以把 pull string 系在一起的,也很容易解决。
-troyd(.);
2019-12-30
(#12565730@0)
-
明线太容易了,不必问。就是不想走。
-2841999(四友);
2019-12-30
(#12565788@0)
-
如果房子有crown molding, 你就把线在墙内往上走,藏在crown molding里面,到位置后再进墙内往下走。我干过。
-ab6949(游牧民族);
2019-12-30
(#12565804@0)
+1
-
有理。感觉楼主直接穿木头方案是高高手才行。我看DIY书上方法是线拉到地面横向走,或者如果上面是阁楼,钓鱼到天花板再横走。
-w4b(w4b);
2019-12-30
(#12565816@0)
-
直接穿木头的话如何在木头上打孔呢?
-thegirlbefore(Jane);
2019-12-30
(#12565822@0)
-
破墙,如下图
-w4b(w4b);
2019-12-30
(#12565847@0)
-
我还以为是隔着dry wall穿线呢,破墙工作量大了。高手不破墙行吗?
-thegirlbefore(Jane);
2019-12-30
(#12565859@0)
-
男人的一根筋,你还没见识过?
-troyd(.);
2019-12-30
(#12565872@0)
-
拆墙角线是可行的,墙角空隙挺大,拆墙角线可能把墙损坏,drywall才一层纸,
-googlebot(bot);
2019-12-30
(#12565874@0)
-
我发现我家的踢脚线都是按在drywall 上的呀,drywall和地面几乎没啥空隙。
-thegirlbefore(Jane);
2019-12-30
(#12565885@0)
-
可以用刀子切点drywall,一般木地板瓷砖都不会紧贴墙,要留空隙的,
-googlebot(bot);
2019-12-30
(#12565953@0)
-
需要一定技术能力。拆墙角线,割下一小条 drywall,走完线再装回墙角线。
细心一点不会有问题。这种“破墙”不需要补墙,有经验师傅会做得不留痕迹。
-w4b(w4b);
2019-12-30
(#12565887@0)
-
没有阁楼,没有地下室,没有molding。
-2841999(四友);
2019-12-30
(#12565824@0)
-
没有 molding 就加一个 molding,算升级。如图:
-w4b(w4b);
2019-12-30
(#12565845@0)
-
把原来的盒子拆卸了,从里面走线,走完线,再安装新的盒子。。。retrofit box。。。
-ballfan(BALLFANS);
2019-12-30
{18}
(#12565808@0)
-
钉子钉在里面,不破墙不可能的,
-googlebot(bot);
2019-12-30
(#12565864@0)
-
这都拿不出来,那就不用继续了。。。这是基本功。。。
-ballfan(BALLFANS);
2019-12-30
{16}
(#12566238@0)
-
先把盒子里的线打开,螺钉都拿出来,然后用个锤子往里敲,直到能看到钉子,然后用个锯子锯掉。小心的话不会破坏drywall
-gta_palace(呄 - 每天乃古);
2019-12-30
(#12565879@0)
-
这个搞过很多,我都是直接把铁盒子用prybar撬下来,再换新的铁盒子。
-zhengsean(IT大叔);
2019-12-30
(#12565892@0)
-
Remove baseboard (remember to use knife to slide cut the caulking) then fish down, open up the wall, fish across then fish up, then reattach baseboard, re caulk.
-jeffrey815(Smartiecat);
2019-12-30
(#12565893@0)
-
这个是最为可行的方法。可以完全不用破墙 - 从上面的铁盒里伸出一根fishing wire, 在baseboard处接好,再拉上去进铁盒。
-lakota(lakota);
2019-12-30
(#12565920@0)
-
最好在铁盒某一面开洞,不然穿线很困难,因为电线太硬了。我觉着横穿几个stud反而是不易。一般是2x4, 太窄了,很容易钻偏。
-lakota(lakota);
2019-12-30
(#12565897@0)
-
我觉得wire fishing 只适用于有conduit的条件下,否则在stud and boxes之间基本没有可能,尤其是对gauge 12/14电线。
-wfhisgood(WFH);
2019-12-30
(#12565963@0)
-
谁家墙里面跑conduit?。。。
-ballfan(BALLFANS);
2019-12-30
(#12566739@0)
-
看来你家豪宅够老的, 请问高寿了? 一般都不采用横穿线, 这样做工程很大.
-yuanfanback(归来的远帆);
2019-12-30
(#12567241@0)
-
什么时候电力可以无线传输就好了。现在开关可以无线遥控,方便多了,电池供电的开关可以安装在任何地方而不用走线。如果电源插座和灯头能安装任何地方,不用走线,用某种无线方式传输120伏特电力,就太方便了。
-w4b(w4b);
2019-12-31
(#12567317@0)
-
这有什么,早就有日程了.具体时间: 驴年, 马月,26 时, 就可以实现.
-yuanfanback(归来的远帆);
2019-12-31
{39}
(#12567358@0)
-
人脑袋就在这 120VAC 里晃来晃去,合适么?
-troyd(.);
2019-12-31
(#12567364@0)
-
会糊墙的话这些都不是什么事情。我以前拉线也怕坡墙。现在直接就把drywall给扯掉。更简单直接
-gta_palace(呄 - 每天乃古);
2019-12-31
(#12567736@0)
+1
-
drywall开孔最简单,也容易修,
-googlebot(bot);
2019-12-31
(#12567802@0)
+1