This topic has been archived. It cannot be replied.
-
枫下家园 / 美丽家居 / 请教:准备关闭车库(水龙头)的水源,但同一根水管隔着墙的另外一个室内的水龙头似乎卡住了,拧起来很吃力,而且关不死,所以车库内的水龙头依然出水。照片中室内的水龙头2头和铜管焊在一起,请问大家要请人换掉这个水龙头吗?还是滴化学试剂?谢谢
-wooddoor(123456);
2019-10-14
{59}
(#12385780@0)
-
如果室外水管伸出不长,冬天室内的水龙头也需要关闭吗?
-wooddoor(123456);
2019-10-14
(#12385783@0)
-
关掉最好
-hammer_king(锤镰帮);
2019-10-14
(#12385853@0)
-
车库的问题不大 车库里基本不会低于零度
-facenorthface(小北);
2019-10-15
(#12386632@0)
-
今年外面-20C,车库出现-6C
-wooddoor(123456);
2019-10-15
(#12387725@0)
-
不用换水龙头。把水龙头里面老化的橡皮圈换掉就行了。
-hammer_king(锤镰帮);
2019-10-14
(#12385852@0)
-
谢谢。不漏水,就是拧不死,什么地方卡住一样。
-wooddoor(123456);
2019-10-14
(#12385953@0)
-
橡皮圈老化后失去弹性,已经悬空了当然拧不死
-hammer_king(锤镰帮);
2019-10-14
(#12385971@0)
-
谢谢。周末先关总闸,然后打开看看。
-wooddoor(123456);
2019-10-14
(#12385993@0)
-
gate阀门必须放在全开或全关位置,否则时间长了就会变形,然后就关不上了
-gta_palace(呄 - 每天乃古);
2019-10-14
(#12385968@0)
-
谢谢,那怎么处理?请水管工重焊接换全新的?
-wooddoor(123456);
2019-10-14
(#12385990@0)
-
你自己会不会拆开来看看?一拆开来就知道是怎么回事了
-hammer_king(锤镰帮);
2019-10-14
(#12385996@0)
-
我没干过,应该可以。曾经自己换过water tanker的drain valve.
-wooddoor(123456);
2019-10-14
(#12386000@0)
-
拆掉,阀门才几块钱,换个球阀。或者把通到外面的管子连到一起,装一个总阀。
-gta_palace(呄 - 每天乃古);
2019-10-14
(#12386008@0)
-
我不会焊接,阀门和水管焊接在一起
-wooddoor(123456);
2019-10-14
(#12386026@0)
-
会也不要随便焊。周围都是可燃物,别把房子烧了。
-kansaslpa(lpa);
2019-10-15
(#12386572@0)
-
两种方案,1,试着换橡皮垫圈。2,锯掉,换新式阀门。PVC和铜管有专门的连接件的,不难。
-kansaslpa(lpa);
2019-10-15
(#12386573@0)
-
你拍个车库水龙头来看看,我也有过同样问题。花了两块钱两分钟解决问题…
-wabuka(waka);
2019-10-15
(#12386219@0)
-
车库里是同样的阀门
-wooddoor(123456);
2019-10-15
(#12386799@0)
-
第1,把总阀关掉
第2打开车库里的水龙头把水放进
的三用一个大扳手把照片中的那个水阀重六角形那个地方 逆时针拧下来
看一下阀芯的情况,顺便彻底开关一下手轮, 确保首轮活动自由 ,密封垫好的话可以装回去。如果不行买一个 相同的阀门把上边的那部分拆下来,装到你就的阀体上就好了,装的时候记住 水阀要开到开的最大位置。
-anexplorer(页于);
2019-10-15
{300}
(#12386629@0)
-
你确定是逆时针?龙头里好像都是顺时针,
-googlebot(bot);
2019-10-15
(#12387786@0)
-
拿一个长的螺丝刀卡进去使劲拧应该拧的动
-facenorthface(小北);
2019-10-15
(#12386633@0)
-
这个还有啥讨论的?换一个,HD,$12块钱。
-hunhunhunhun(不知道);
2019-10-15
(#12386634@0)
-
自己能换就不会到这儿来了
-hammer_king(锤镰帮);
2019-10-15
(#12386667@0)
-
一并谢谢大家。这些年有很多第一次,比如装洗碗机,换water tank draining valve,换电源开关等,离不开大家的帮助,谢谢。
-wooddoor(123456);
2019-10-15
(#12386803@0)
-
刚去homeepot,homedpot建议去其它plumbing store,他们没有同型号的阀门
-wooddoor(123456);
2019-10-15
(#12387720@0)
-
你这个是闸阀,容易关不紧,拆下来去店里买个同样尺寸的球阀换上就没有问题了
-doris99(Doris);
2019-10-15
(#12387890@0)
-
还有金属螺纹连接的一定要用特氟龙缠好
-doris99(Doris);
2019-10-16
(#12387953@0)
-
谢谢我也喜欢球阀,但需要焊接吧。
-wooddoor(123456);
2019-10-16
(#12388211@0)
-
为什么?可以螺纹连接啊
-doris99(Doris);
2019-10-16
(#12388450@0)
-
铜管上没有看到螺纹,要用工具弄出螺纹吗?
-wooddoor(123456);
2019-10-16
(#12388530@0)
-
那你以前是怎么冬的?今年车库里很冷, 必须关掉然后做一些安全处理, 我看还是花点钱请人来处理,
-yuanfanback(归来的远帆);
2019-10-16
(#12388179@0)
-
去年能关死,有点吃力,今年完全不行了。我刚去了Wolseley plumbing,他们看图片后说喷penetration oil就行,我回家试试。
-wooddoor(123456);
2019-10-16
(#12388217@0)
-
那赶快换个球阀, 据说今年冬天很吓人的,呼吁各位尽快做好过冬的准备.
-yuanfanback(归来的远帆);
2019-10-16
(#12388244@0)
-
要焊接一起吗
-wooddoor(123456);
2019-10-16
(#12388403@0)
-
根本不要这么麻烦,我和你说过2块钱2分钟的事情。以为我在忽悠你…
-wabuka(waka);
2019-10-16
(#12388516@0)
-
告诉我怎么操作?谢谢
-wooddoor(123456);
2019-10-16
(#12388520@0)
-
按我说的把那个Bonnet拧下来, 发个照片给我看看, 你那个发应该就是一个 Globe valve.
-anexplorer(页于);
2019-10-16
(#12388556@0)
-
不是说了嘛,车库水龙头的照片呢…
-wabuka(waka);
2019-10-16
(#12388592@0)
-
请看这个,或有帮助,
-peasantca(加国农民);
2019-10-16
{126}
(#12388629@0)
-
Disassembling a Gate Valve - YouTube
-peasantca(加国农民);
2019-10-16
{126}
(#12388635@0)
-
先试试最简单的, 用WD-40试下
-peasantca(加国农民);
2019-10-16
(#12388668@0)
-
可以买不需要 焊的那种,很方便.
-yuanfanback(归来的远帆);
2019-10-31
(#12417348@0)
-
用板手整个阀芯拆下,去买个新的换掉。图中这种款式的我知道Low's有得卖,Homedepot , Rona都没有。
-jiaji(加吉);
2019-10-30
(#12416973@0)