×

Loading...
Ad by
  • 最优利率和cashback可以申请特批,好信用好收入offer更好。请点链接扫码加微信咨询,Scotiabank -- Nick Zhang 6478812600。
Ad by
  • 最优利率和cashback可以申请特批,好信用好收入offer更好。请点链接扫码加微信咨询,Scotiabank -- Nick Zhang 6478812600。

各位大虾,谁能告诉我以下quiz的标准答案,先谢了! (从一agency 得来)

本文发表在 rolia.net 枫下论坛>
> 1. What type of connector is on a 10BaseT network card?
> [ ] a) T-connector
> [ ] b) RJ-45
> [ ] c) RJ-11
> [ ] d) Dix connector
> [ ] e) Any of the above
>
>
> 2. How many devices can an IDE controller support?
> [ ] a) 2
> [ ] b) 3
> [ ] c) 4
> [ ] d) 7
>
>
>
> 3. How wide is the standard I/O bus on a PCI motherboard?
> [ ] a) 3 inches
> [ ] b) 16 bytes
> [ ] c) 16 bits
> [ ] d) 32 bytes
> [ ] e) 32 bits
>
>
> 4. How many DIMMs are required to complete a memory bank on a standard
> Pentium motherboard?
> [ ] a) One
> [ ] b) Two
> [ ] c) Four
> [ ] d) Eight
> [ ] e) Any of the above depending on the power configuration, AT or ATX
>
>
> 5. As a rule of thumb, where does pin one on an IDE ribbon cable face
> when plugged onto the hard disk drive?
> [ ] a) The right side
> [ ] b) The left side
> [ ] c) The side nearest the power connector
> [ ] d) The side closest to the master/slave jumpers
>
>
> 6. After adding a second IDE hard drive to a new Pentium III desktop
> computer, the system will not boot the operating system. There are no
> POST error messages. What is the most likely cause?
> [ ] a) The cables are not connected properly
> [ ] b) The drives are not setup as master & slave
> [ ] c) The ribbon cable is not terminated
> [ ] d) There is a short-circuit somewhere in the system
>
>
> 7. Which end of a SCSI bus must be terminated?
> [ ] a) All open connectors
> [ ] b) Only the free ends of the cable
> [ ] c) Both physical ends
> [ ] d) New SCSI adapters don't need termination
> [ ] e) The last device in the chain
>
>
> 8. To install a SCSI hard drive at ID 5, which ID jumper(s) must be shorted?
> [ ] a) Jumpers 1 and 4
> [ ] b) Jumpers 2 and 3
> [ ] c) Jumpers 0 and 2
> [ ] d) Jumpers 0, 1, and 2
>
>
> 9. What is the default port address and interrupt for COM2?
> [ ] a) 03F8, IRQ 4
> [ ] b) 02F8, IRQ 4
> [ ] c) 0378, IRQ 7
> [ ] d) 03F8, IRQ 3
> [ ] e) 02F8, IRQ 3
>
>
> 10. When installing a modem that is set explicitly to COM2, what
> resource should be disabled in the system setup (CMOS)?
> [ ] a) Software (Xon/Xoff)
> [ ] b) Interpreted response
> [ ] c) COM2
> [ ] d) IRQ 4
> [ ] e) All of the above
>
>
> 11. After upgrading your computer's CPU from a 333 MHz Celeron to a new
> Pentium II 450 MHz processor, the system becomes unstable.
> Choose the 2 most likely causes from the following:
> [ ] a) Jumper settings weren't switched from Celeron to Pentium II
> [ ] b) Celeron motherboards do not support Pentium II CPUs.
> [ ] c) Motherboard does not have a 100Mhz front side bus.
> [ ] d) The on-board chipset is not compatible with Pentium II CPUs.
> [ ] e) The cooling fan is not functioning properly.
> [ ] f) The system is using 66Mhz RAM in a 100Mhz system.
>
>
> 12. What is the theoretical maximum throughput of a 10BaseT Ethernet
> network?
> [ ] a) 10 MHz
> [ ] b) 10 Mbps
> [ ] c) 100 MHz
> [ ] d) 100 Mbps
> [ ] e) Depends on the protocol used over the LAN
>
>
> 13. Which of the following network protocols are directly supported by
> Microsoft? (Choose all that apply).
> [ ] a) TCP/IP
> [ ] b) NetBEUI
> [ ] c) IPX ODI
> [ ] d) Token Ring
> [ ] e) IPX/SPX Compatible Protocol
>
>
> 14. Does a router require an IP address to forward packets to a
> different subnet under TCP/IP?
> [ ] a) No, a router builds a routing table of all subnets so that it
> does not need to forward packets.
> [ ] b) Yes, but only if the other subnet is in another domain.
> [ ] c) Yes, a router forwards IP packets to different subnets.
>
>
> 15. What is the most likely problem if an administrator is unable to
> add a new user account or change a user's password in a single domain
> environment? (Assume the administrator has full administrative rights.)
> [ ] a) The Administrator account has been locked out.
> [ ] b) The user name already exists, or the user is already logged in
> to the account.
> [ ] c) The primary domain controller (PDC) is down or offline.
> [ ] d) The administrator must be logged in at the PDC or BDC.
>
>
> 16. If you are establishing a trust relationship between Domain A and
> Domain B, which utility would you use to create the trust?
> [ ] a) Server Manager
> [ ] b) Control Panel -- Server
> [ ] c) User Manager for Domains
> [ ] d) System Policy Editor
> [ ] e) Control Panel -- Services
>
>
> 17. When establishing a one-way trust relationship between
> Domain A (Accounts Domain) and Domain B (Resource Domain), which
> domain is the trusting domain?
> [ ] a) Domain A or B, depending which is created first
> [ ] b) Domain B is the trusting Domain
> [ ] c) Domain A is the trusting Domain
>
>
> 18. What special designations does Active Directory (AD) give to domain
> controllers? (Choose 2.)
> [ ] a) PDC
> [ ] b) Global Catalog (GC) server
> [ ] c) Master Catalog server
> [ ] d) Operations Master
>
>
> 19. What important functions does a Global Catalog (GC) server perform for
> users in Active Directory (AD)? (Choose 2.)
> [ ] a) A GC server lets a user search the entire forest to find
> directory information.
> [ ] b) A GC server maintains a list of the user's resources.
> [ ] c) A GC server enables the logon process by providing universal group
> membership information to the domain controller.
> [ ] d) A GC server helps users find services anywhere in the world.
>
>
> 20. As the administrator for your company, what can you do to decrease the
> traffic that results from queries to the Global Catalog (GC) across sites?
> (Choose the best answer.)
> [ ] a) Limit GC searches to the local site.
> [ ] b) Create separate forests so that searches remain local.
> [ ] c) Create additional GC servers so that the GC is available locally.
> [ ] d) Create a local catalog so that searches don't cross WAN links.
>
>
> 21. What is the native capacity of DLT IV tape?
> [ ] a) 20GB
> [ ] b) 35GB
> [ ] c) 40GB
> [ ] d) All of the above
> [ ] e) None of the above
>
>
> 22. If you have a 20GB hard drive, a 36GB hard drive, and a 50GB hard
> drive all configured in a RAID level 5 hardware array, approximately
> how much total disk space should be available?
> [ ] a) 40GB
> [ ] b) 56GB
> [ ] c) 86GB
> [ ] d) 106GB
> [ ] e) none of the above
>
>
> 23. Regarding the functional differences between AT and ATX power
> supplies, which statement is true?
> [ ] a) AT supports soft power-on and 3.3V, ATX does not.
> [ ] b) ATX supports soft power-on, AT supplies 3.3V.
> [ ] c) AT supports soft power-on, ATX supplies 3.3V.
> [ ] d) ATX supports soft power-on and 3.3V, AT does not.
>
>
> 24. What is the theoretical maximum bandwidth of a T3?
> [ ] a) 1.5Mbps
> [ ] b) 15Mbps
> [ ] c) 35Mbps
> [ ] d) 45Mbps
>
>
> 25. An Outlook 98 user is working offline with offline folders.
> The user tries to access the address book to address his/her message and
> discovers that the list is empty or not available.
> Why might this be?
> [ ] a) The user is tyring to connect via an Internet proxy server.
> [ ] b) The user has never downloaded the address book from the server.
> [ ] c) The user's address book is not configured for offline use.
> [ ] d) The user must connect to the server to access the address book.
> [ ] e) The user does not have enough rights to access the address book.
>
>
> 26. Which of the following scenarios represent appropriate situations in
> which to use the Last Known Good Configuration in Windows 2000 Professional?
> (Choose all that apply.)
> [ ] a) You accidentally disable a critical device driver.
> [ ] b) You install a new video driver and can't restart the system.
> [ ] c) You copy a new driver over an old one while the old one is
> active and subsequently encounter problems.
> [ ] d) You install a new device driver, restart Win2K, and the system
> stops responding.
> [ ] e) You experience a startup failure caused by hardware failures
> or corrupted files.
>
>
>
>
> General
> List 3 to 5 procedures you would implement to help your company
> prepare for a total data loss.
>
>
>
> List 3 to 5 procedures you would implement to help your company
> roll out a new software package, such as Microsoft Office 2000.
>
>更多精彩文章及讨论,请光临枫下论坛 rolia.net
Sign in and Reply Report

Replies, comments and Discussions:

  • 工作学习 / IT技术讨论 / 各位大虾,谁能告诉我以下quiz的标准答案,先谢了! (从一agency 得来)
    本文发表在 rolia.net 枫下论坛>
    > 1. What type of connector is on a 10BaseT network card?
    > [ ] a) T-connector
    > [ ] b) RJ-45
    > [ ] c) RJ-11
    > [ ] d) Dix connector
    > [ ] e) Any of the above
    >
    >
    > 2. How many devices can an IDE controller support?
    > [ ] a) 2
    > [ ] b) 3
    > [ ] c) 4
    > [ ] d) 7
    >
    >
    >
    > 3. How wide is the standard I/O bus on a PCI motherboard?
    > [ ] a) 3 inches
    > [ ] b) 16 bytes
    > [ ] c) 16 bits
    > [ ] d) 32 bytes
    > [ ] e) 32 bits
    >
    >
    > 4. How many DIMMs are required to complete a memory bank on a standard
    > Pentium motherboard?
    > [ ] a) One
    > [ ] b) Two
    > [ ] c) Four
    > [ ] d) Eight
    > [ ] e) Any of the above depending on the power configuration, AT or ATX
    >
    >
    > 5. As a rule of thumb, where does pin one on an IDE ribbon cable face
    > when plugged onto the hard disk drive?
    > [ ] a) The right side
    > [ ] b) The left side
    > [ ] c) The side nearest the power connector
    > [ ] d) The side closest to the master/slave jumpers
    >
    >
    > 6. After adding a second IDE hard drive to a new Pentium III desktop
    > computer, the system will not boot the operating system. There are no
    > POST error messages. What is the most likely cause?
    > [ ] a) The cables are not connected properly
    > [ ] b) The drives are not setup as master & slave
    > [ ] c) The ribbon cable is not terminated
    > [ ] d) There is a short-circuit somewhere in the system
    >
    >
    > 7. Which end of a SCSI bus must be terminated?
    > [ ] a) All open connectors
    > [ ] b) Only the free ends of the cable
    > [ ] c) Both physical ends
    > [ ] d) New SCSI adapters don't need termination
    > [ ] e) The last device in the chain
    >
    >
    > 8. To install a SCSI hard drive at ID 5, which ID jumper(s) must be shorted?
    > [ ] a) Jumpers 1 and 4
    > [ ] b) Jumpers 2 and 3
    > [ ] c) Jumpers 0 and 2
    > [ ] d) Jumpers 0, 1, and 2
    >
    >
    > 9. What is the default port address and interrupt for COM2?
    > [ ] a) 03F8, IRQ 4
    > [ ] b) 02F8, IRQ 4
    > [ ] c) 0378, IRQ 7
    > [ ] d) 03F8, IRQ 3
    > [ ] e) 02F8, IRQ 3
    >
    >
    > 10. When installing a modem that is set explicitly to COM2, what
    > resource should be disabled in the system setup (CMOS)?
    > [ ] a) Software (Xon/Xoff)
    > [ ] b) Interpreted response
    > [ ] c) COM2
    > [ ] d) IRQ 4
    > [ ] e) All of the above
    >
    >
    > 11. After upgrading your computer's CPU from a 333 MHz Celeron to a new
    > Pentium II 450 MHz processor, the system becomes unstable.
    > Choose the 2 most likely causes from the following:
    > [ ] a) Jumper settings weren't switched from Celeron to Pentium II
    > [ ] b) Celeron motherboards do not support Pentium II CPUs.
    > [ ] c) Motherboard does not have a 100Mhz front side bus.
    > [ ] d) The on-board chipset is not compatible with Pentium II CPUs.
    > [ ] e) The cooling fan is not functioning properly.
    > [ ] f) The system is using 66Mhz RAM in a 100Mhz system.
    >
    >
    > 12. What is the theoretical maximum throughput of a 10BaseT Ethernet
    > network?
    > [ ] a) 10 MHz
    > [ ] b) 10 Mbps
    > [ ] c) 100 MHz
    > [ ] d) 100 Mbps
    > [ ] e) Depends on the protocol used over the LAN
    >
    >
    > 13. Which of the following network protocols are directly supported by
    > Microsoft? (Choose all that apply).
    > [ ] a) TCP/IP
    > [ ] b) NetBEUI
    > [ ] c) IPX ODI
    > [ ] d) Token Ring
    > [ ] e) IPX/SPX Compatible Protocol
    >
    >
    > 14. Does a router require an IP address to forward packets to a
    > different subnet under TCP/IP?
    > [ ] a) No, a router builds a routing table of all subnets so that it
    > does not need to forward packets.
    > [ ] b) Yes, but only if the other subnet is in another domain.
    > [ ] c) Yes, a router forwards IP packets to different subnets.
    >
    >
    > 15. What is the most likely problem if an administrator is unable to
    > add a new user account or change a user's password in a single domain
    > environment? (Assume the administrator has full administrative rights.)
    > [ ] a) The Administrator account has been locked out.
    > [ ] b) The user name already exists, or the user is already logged in
    > to the account.
    > [ ] c) The primary domain controller (PDC) is down or offline.
    > [ ] d) The administrator must be logged in at the PDC or BDC.
    >
    >
    > 16. If you are establishing a trust relationship between Domain A and
    > Domain B, which utility would you use to create the trust?
    > [ ] a) Server Manager
    > [ ] b) Control Panel -- Server
    > [ ] c) User Manager for Domains
    > [ ] d) System Policy Editor
    > [ ] e) Control Panel -- Services
    >
    >
    > 17. When establishing a one-way trust relationship between
    > Domain A (Accounts Domain) and Domain B (Resource Domain), which
    > domain is the trusting domain?
    > [ ] a) Domain A or B, depending which is created first
    > [ ] b) Domain B is the trusting Domain
    > [ ] c) Domain A is the trusting Domain
    >
    >
    > 18. What special designations does Active Directory (AD) give to domain
    > controllers? (Choose 2.)
    > [ ] a) PDC
    > [ ] b) Global Catalog (GC) server
    > [ ] c) Master Catalog server
    > [ ] d) Operations Master
    >
    >
    > 19. What important functions does a Global Catalog (GC) server perform for
    > users in Active Directory (AD)? (Choose 2.)
    > [ ] a) A GC server lets a user search the entire forest to find
    > directory information.
    > [ ] b) A GC server maintains a list of the user's resources.
    > [ ] c) A GC server enables the logon process by providing universal group
    > membership information to the domain controller.
    > [ ] d) A GC server helps users find services anywhere in the world.
    >
    >
    > 20. As the administrator for your company, what can you do to decrease the
    > traffic that results from queries to the Global Catalog (GC) across sites?
    > (Choose the best answer.)
    > [ ] a) Limit GC searches to the local site.
    > [ ] b) Create separate forests so that searches remain local.
    > [ ] c) Create additional GC servers so that the GC is available locally.
    > [ ] d) Create a local catalog so that searches don't cross WAN links.
    >
    >
    > 21. What is the native capacity of DLT IV tape?
    > [ ] a) 20GB
    > [ ] b) 35GB
    > [ ] c) 40GB
    > [ ] d) All of the above
    > [ ] e) None of the above
    >
    >
    > 22. If you have a 20GB hard drive, a 36GB hard drive, and a 50GB hard
    > drive all configured in a RAID level 5 hardware array, approximately
    > how much total disk space should be available?
    > [ ] a) 40GB
    > [ ] b) 56GB
    > [ ] c) 86GB
    > [ ] d) 106GB
    > [ ] e) none of the above
    >
    >
    > 23. Regarding the functional differences between AT and ATX power
    > supplies, which statement is true?
    > [ ] a) AT supports soft power-on and 3.3V, ATX does not.
    > [ ] b) ATX supports soft power-on, AT supplies 3.3V.
    > [ ] c) AT supports soft power-on, ATX supplies 3.3V.
    > [ ] d) ATX supports soft power-on and 3.3V, AT does not.
    >
    >
    > 24. What is the theoretical maximum bandwidth of a T3?
    > [ ] a) 1.5Mbps
    > [ ] b) 15Mbps
    > [ ] c) 35Mbps
    > [ ] d) 45Mbps
    >
    >
    > 25. An Outlook 98 user is working offline with offline folders.
    > The user tries to access the address book to address his/her message and
    > discovers that the list is empty or not available.
    > Why might this be?
    > [ ] a) The user is tyring to connect via an Internet proxy server.
    > [ ] b) The user has never downloaded the address book from the server.
    > [ ] c) The user's address book is not configured for offline use.
    > [ ] d) The user must connect to the server to access the address book.
    > [ ] e) The user does not have enough rights to access the address book.
    >
    >
    > 26. Which of the following scenarios represent appropriate situations in
    > which to use the Last Known Good Configuration in Windows 2000 Professional?
    > (Choose all that apply.)
    > [ ] a) You accidentally disable a critical device driver.
    > [ ] b) You install a new video driver and can't restart the system.
    > [ ] c) You copy a new driver over an old one while the old one is
    > active and subsequently encounter problems.
    > [ ] d) You install a new device driver, restart Win2K, and the system
    > stops responding.
    > [ ] e) You experience a startup failure caused by hardware failures
    > or corrupted files.
    >
    >
    >
    >
    > General
    > List 3 to 5 procedures you would implement to help your company
    > prepare for a total data loss.
    >
    >
    >
    > List 3 to 5 procedures you would implement to help your company
    > roll out a new software package, such as Microsoft Office 2000.
    >
    >更多精彩文章及讨论,请光临枫下论坛 rolia.net
    • Let me 踹
      本文发表在 rolia.net 枫下论坛> 1. What type of connector is on a 10BaseT network card?
      > [ ] a) T-connector
      > [ ] b) RJ-45
      > [ ] c) RJ-11
      > [ ] d) Dix connector
      > [ ] e) Any of the above

      B (不肯定,时间太久了,忘了)

      > 2. How many devices can an IDE controller support?
      > [ ] a) 2
      > [ ] b) 3
      > [ ] c) 4
      > [ ] d) 7

      C

      > 3. How wide is the standard I/O bus on a PCI motherboard?
      > [ ] a) 3 inches
      > [ ] b) 16 bytes
      > [ ] c) 16 bits
      > [ ] d) 32 bytes
      > [ ] e) 32 bits

      E

      > 4. How many DIMMs are required to complete a memory bank on a standard Pentium motherboard?
      > [ ] a) One
      > [ ] b) Two
      > [ ] c) Four
      > [ ] d) Eight
      > [ ] e) Any of the above depending on the power configuration, AT or ATX

      A

      > 5. As a rule of thumb, where does pin one on an IDE ribbon cable face
      > when plugged onto the hard disk drive?
      > [ ] a) The right side
      > [ ] b) The left side
      > [ ] c) The side nearest the power connector
      > [ ] d) The side closest to the master/slave jumpers

      C

      > 6. After adding a second IDE hard drive to a new Pentium III desktop
      > computer, the system will not boot the operating system. There are no
      > POST error messages. What is the most likely cause?
      > [ ] a) The cables are not connected properly
      > [ ] b) The drives are not setup as master & slave
      > [ ] c) The ribbon cable is not terminated
      > [ ] d) There is a short-circuit somewhere in the system

      B

      > 7. Which end of a SCSI bus must be terminated?
      > [ ] a) All open connectors
      > [ ] b) Only the free ends of the cable
      > [ ] c) Both physical ends
      > [ ] d) New SCSI adapters don't need termination
      > [ ] e) The last device in the chain

      E ?

      > 8. To install a SCSI hard drive at ID 5, which ID jumper(s) must be shorted?
      > [ ] a) Jumpers 1 and 4
      > [ ] b) Jumpers 2 and 3
      > [ ] c) Jumpers 0 and 2
      > [ ] d) Jumpers 0, 1, and 2

      C

      > 9. What is the default port address and interrupt for COM2?
      > [ ] a) 03F8, IRQ 4
      > [ ] b) 02F8, IRQ 4
      > [ ] c) 0378, IRQ 7
      > [ ] d) 03F8, IRQ 3
      > [ ] e) 02F8, IRQ 3

      E

      > 10. When installing a modem that is set explicitly to COM2, what
      > resource should be disabled in the system setup (CMOS)?
      > [ ] a) Software (Xon/Xoff)
      > [ ] b) Interpreted response
      > [ ] c) COM2
      > [ ] d) IRQ 4
      > [ ] e) All of the above

      C

      > 11. After upgrading your computer's CPU from a 333 MHz Celeron to a new
      > Pentium II 450 MHz processor, the system becomes unstable.
      > Choose the 2 most likely causes from the following:
      > [ ] a) Jumper settings weren't switched from Celeron to Pentium II
      > [ ] b) Celeron motherboards do not support Pentium II CPUs.
      > [ ] c) Motherboard does not have a 100Mhz front side bus.
      > [ ] d) The on-board chipset is not compatible with Pentium II CPUs.
      > [ ] e) The cooling fan is not functioning properly.
      > [ ] f) The system is using 66Mhz RAM in a 100Mhz system.

      EF

      > 12. What is the theoretical maximum throughput of a 10BaseT Ethernet
      > network?
      > [ ] a) 10 MHz
      > [ ] b) 10 Mbps
      > [ ] c) 100 MHz
      > [ ] d) 100 Mbps
      > [ ] e) Depends on the protocol used over the LAN

      B

      > 13. Which of the following network protocols are directly supported by
      > Microsoft? (Choose all that apply).
      > [ ] a) TCP/IP
      > [ ] b) NetBEUI
      > [ ] c) IPX ODI
      > [ ] d) Token Ring
      > [ ] e) IPX/SPX Compatible Protocol

      ABE

      > 14. Does a router require an IP address to forward packets to a
      > different subnet under TCP/IP?
      > [ ] a) No, a router builds a routing table of all subnets so that it
      > does not need to forward packets.
      > [ ] b) Yes, but only if the other subnet is in another domain.
      > [ ] c) Yes, a router forwards IP packets to different subnets.

      C

      > 15. What is the most likely problem if an administrator is unable to
      > add a new user account or change a user's password in a single domain
      > environment? (Assume the administrator has full administrative rights.)
      > [ ] a) The Administrator account has been locked out.
      > [ ] b) The user name already exists, or the user is already logged in
      > to the account.
      > [ ] c) The primary domain controller (PDC) is down or offline.
      > [ ] d) The administrator must be logged in at the PDC or BDC.

      C ?

      > 16. If you are establishing a trust relationship between Domain A and
      > Domain B, which utility would you use to create the trust?
      > [ ] a) Server Manager
      > [ ] b) Control Panel -- Server
      > [ ] c) User Manager for Domains
      > [ ] d) System Policy Editor
      > [ ] e) Control Panel -- Services

      C

      > 17. When establishing a one-way trust relationship between
      > Domain A (Accounts Domain) and Domain B (Resource Domain), which
      > domain is the trusting domain?
      > [ ] a) Domain A or B, depending which is created first
      > [ ] b) Domain B is the trusting Domain
      > [ ] c) Domain A is the trusting Domain

      B

      > 18. What special designations does Active Directory (AD) give to domain
      > controllers? (Choose 2.)
      > [ ] a) PDC
      > [ ] b) Global Catalog (GC) server
      > [ ] c) Master Catalog server
      > [ ] d) Operations Master

      ?

      > 19. What important functions does a Global Catalog (GC) server perform for
      > users in Active Directory (AD)? (Choose 2.)
      > [ ] a) A GC server lets a user search the entire forest to find
      > directory information.
      > [ ] b) A GC server maintains a list of the user's resources.
      > [ ] c) A GC server enables the logon process by providing universal group
      > membership information to the domain controller.
      > [ ] d) A GC server helps users find services anywhere in the world.

      ?

      > 20. As the administrator for your company, what can you do to decrease the
      > traffic that results from queries to the Global Catalog (GC) across sites?
      > (Choose the best answer.)
      > [ ] a) Limit GC searches to the local site.
      > [ ] b) Create separate forests so that searches remain local.
      > [ ] c) Create additional GC servers so that the GC is available locally.
      > [ ] d) Create a local catalog so that searches don't cross WAN links.

      ?

      > 21. What is the native capacity of DLT IV tape?
      > [ ] a) 20GB
      > [ ] b) 35GB
      > [ ] c) 40GB
      > [ ] d) All of the above
      > [ ] e) None of the above

      C?

      > 22. If you have a 20GB hard drive, a 36GB hard drive, and a 50GB hard
      > drive all configured in a RAID level 5 hardware array, approximately
      > how much total disk space should be available?
      > [ ] a) 40GB
      > [ ] b) 56GB
      > [ ] c) 86GB
      > [ ] d) 106GB
      > [ ] e) none of the above

      A

      > 23. Regarding the functional differences between AT and ATX power
      > supplies, which statement is true?
      > [ ] a) AT supports soft power-on and 3.3V, ATX does not.
      > [ ] b) ATX supports soft power-on, AT supplies 3.3V.
      > [ ] c) AT supports soft power-on, ATX supplies 3.3V.
      > [ ] d) ATX supports soft power-on and 3.3V, AT does not.

      D

      > 24. What is the theoretical maximum bandwidth of a T3?
      > [ ] a) 1.5Mbps
      > [ ] b) 15Mbps
      > [ ] c) 35Mbps
      > [ ] d) 45Mbps

      D?

      > 25. An Outlook 98 user is working offline with offline folders.
      > The user tries to access the address book to address his/her message and
      > discovers that the list is empty or not available.
      > Why might this be?
      > [ ] a) The user is tyring to connect via an Internet proxy server.
      > [ ] b) The user has never downloaded the address book from the server.
      > [ ] c) The user's address book is not configured for offline use.
      > [ ] d) The user must connect to the server to access the address book.
      > [ ] e) The user does not have enough rights to access the address book.

      ?

      > 26. Which of the following scenarios represent appropriate situations in
      > which to use the Last Known Good Configuration in Windows 2000 Professional?
      > (Choose all that apply.)
      > [ ] a) You accidentally disable a critical device driver.
      > [ ] b) You install a new video driver and can't restart the system.
      > [ ] c) You copy a new driver over an old one while the old one is
      > active and subsequently encounter problems.
      > [ ] d) You install a new device driver, restart Win2K, and the system
      > stops responding.
      > [ ] e) You experience a startup failure caused by hardware failures
      > or corrupted files.
      >
      >
      >
      >
      > General
      > List 3 to 5 procedures you would implement to help your company
      > prepare for a total data loss.

      Hire new guys.

      > List 3 to 5 procedures you would implement to help your company
      > roll out a new software package, such as Microsoft Office 2000.

      Hire Egg.更多精彩文章及讨论,请光临枫下论坛 rolia.net
      • I didn't read through, but you are wrong at the second one. It should be 2.
        • Why? you can install 4 HDD/CDROMs to IDE. I think there is one controller on motherboard.
          • Unfortunatly ( or luckly), there are two. They are the master one and the secondary one.
            • Since almost 7-8 years ago, a PC can connect to 4 IDE devices.
              • But they are on 2 controllers. So 2 for each controller.
                • but on one chip right? how to count ONE controller?
                  • Hmm, I think you are right. Those 2 are channels, not controllers. The 2 channels are on the same controller. I got my concept mixed up. Thank you for make that clear for me!
      • #4 is wrong, I think 2 slots make one Bank.
        • That's for SIMM. For DIMM, one slot can make one bank.
      • #22 E?
        • a) 40GB 这么老的贴居然还能回
    • Hi, What kind of position it is? It seems coming from one boss of Zhong1 Guan1 Cun1.
      • no, truely from canada
    • 为什么现在中介都要考试啦? 以前没听说要考试呀
    • 这是测验什么的题?
    • 有测试Java , OOP , EJB , XML 相关的题目吗???!!!